Filter
Top Products
GB
2524
Recording a Programme Immediately
OK
6
R
E
C
M
E
N
U
A
U
D
I
O
S
P
E
E
D
T
V
/
V
C
R
OK
★
5
Protecting a Recorded Cassette
Video cassettes have a safety tab to prevent accidental erasure.
When this tab has been removed, you cannot
record on the tape.
1 If you wish to protect a cassette, break off the tab using a small
screwdriver.
2 To re-record over a protected cassette (safety tab broken), cover
the hole with adhesive tape.
1
NICAM programmes are divided into 3 types. NICAM Stereo,
NICAM Mono and Bilingual (transmission in another language).
NICAM programmes are always accompanied by a standard mono
sound broadcast and you can select the desired sound.
Please refer to page 34.
1 Press MENU on the remote control.
Result
: The programming menu is displayed.
2 Press the corresponding
"
,
❷!
or
➛
,
❿
buttons to select the
FUNZIONI option.
3 Press the OK button to select this option.
Result
: The FUNZIONI menu is displayed.
4 Press the corresponding
"
or
❷
buttons, until the cursor is
placed in front of the
NICAM option.
5 To... Press
➛
or
❿
, until...
Mono mode NO is displayed.
NO: Only set at this position to record the
standard mono sound during a NICAM
broadcast if the stereo sound is
distorted due to inferior reception
conditions.
NICAM mode SI is displayed.
SI: Normally set at this position.
6 On completion, press MENU twice to exit the menu.
NICAM
★
(SV-635X/SV-631X/SV-6315X/SV-613X Only)
O
PTIONS
MENU :SI
DURATA NASTRO :E180
NORMA COLORE :AUTO
IPC :SI
16:9 :AUTO
❿
NICAM :SI
"❷
❿
USCITA:MENU
DISP./
VOL PROG/TRK
U
A
U
D
I
O
DISPLAY
TRK PROG
U
A
U
D
I
O
4
4
4
4
Before recording a programme, you must have preset the corres-
ponding station (unless you are recording via an external video
source). If you have not done so, refer to pages 18 and 19.
1 Switch on the television.
2 To monitor the programme being recorded, select the television
channel reserved for use with your VCR (or the AV input if used).
3 Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result
: The VCR is switched on automatically.
4 Select:
◆
The station to be recorded using the
PROG/TRK (
"
or
❷
) /
PROG (
"
or
❷
)
buttons
or
◆ The AV1, AV2 or AUX
★
(SV-635X/SV-631X/SV-6315X/
SV-6313X/SV-530X/SV-435X/SV-235X only) source using
the INPUT button for a satellite tuner or external video source
Result: The station number is displayed and the programme
can be seen on the television.
★
With SV-635X/SV-631X/SV-6315X-SV-6313X/SV-530X/SV-435X/
SV-431X, you can select the recording speed (SP/LP). Press the
SPEED button.
5 Hold REC (
●
) down for a while to start recording.
Result
:
The record indicator appears on the television and VCR
display. An index is recorded on the tape (see page 36).
6 To stop recording, press
■
once.
➢ ◆ If the cassette is ejected when you start recording,
check that the safety tab is intact or the opening is
covered with adhesive tape.
◆ If you reach the end of the tape while recording, the
cassette rewinds automatically.
★
(SV-635X)
★
(SV-631X/SV-6315X/SV-6313X/
SV-530X/SV-435X/SV-431X/SV-235X/
SV-231X/ SV-2315X/SV-2313X)