Filter
Top Products
4
CONNECTIONS
INPUT
Note:
You can connect audio equipment
with a stereo or monaural plug. When
you connect a stereo plug, the MPS-50
converts the stereo output to monaural.
Use a phone cable (available at your lo-
cal RadioShack store) with a
1
/
4
-inch
(6.35 mm) plug to connect an electric
guitar, keyboard, or high impedance mi-
crophone to the
HIGH
input jack of
Channel 1 and/or Channel 2.
Use a phone cable with a
1
/
4
-inch (6.35
mm) plug to connect a low impedance
(200–600 ohms) microphone to the
LOW
jack of Channel 1 and/or Channel 2.
OUTPUT
To play the MPS-50's output signal
through your sound system, connect
one end of an audio patch cord (avail-
able at your local RadioShack store)
with a
1
/
4
-inch (6.35 mm) phone plug to
the MPS-50's
LINE OUT
jack. Then con-
nect the other end to your amplifier/re-
ceiver/mixer's input jack.
SEND AND RETURN
To send the MPS-50's signal to a sound
effect device, such as an echo reverb or
digital sampler processor, connect a
phone cable (available at your local Ra-
dioShack store) with a
1
/
4
-inch (6.35 mm)
plug to the MPS-50’s
SEND
(output)
jack, then connect the other end to the
sound effect device’s input jack.
To receive signal from the connected
device, connect a phone cable with a
1
/
4
-
inch (6.35 mm) plug to the MPS-50’s
RETURN
jack, then connect the other
end to the device’s output jack.
REVERB REMOTE
You can connect an optional remote
footswitch to the MPS-50’s
REVERB RE-
MOTE
jack and use the switch to control
reverb effects.
POWER
Note:
Before you connect the MPS-50
to AC power, set
POWER
to the off (out)
position and
MASTER
to
MIN
.
Connect the female jack end of the sup-
plied power cord to the AC jack on the
back of the MPS-50, then connect the
other end to a standard AC outlet.
CA
UT
ION
RISK OF ELECTRIC
DO NOT OPEN
GUITAR AMPLIFIER
POWER SUPPLY: ~120V 60Hz 150W (FUSE 2A
250V)
Custom Manufactured in China
for RadioShack , A Division of Tandy
Corporation, Fort Worth, TX 76102
CAT. NO. 32-2046
MPS-50
115703
COMMERCIAL AUDIO
EQUIPMENT
CAUTION TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD
RECEPTACLE
~120V AC 60Hz
150 W
FUSE 2A
250V
CAUTION DISCONNECT SUPPLY CORD BEFORE CHANGING
CAUTION FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE
ONLY
POWER
PHONES LINE
OUT
RETURN SEND REVERB
REMOTE
PHONES LINE
OUT
RETURN SEND REVERB
REMOTE
CA
UT
ION
RISK OF ELECTRIC
DO NOT OPEN
GUITAR AMPLIFIER
POWER SUPPLY: ~120V 60Hz 150W (FUSE 2A
250V)
Custom Manufactured in China
for RadioShack , A Division of Tandy
Corporation, Fort Worth, TX 76102
CAT. NO. 32-2046
MPS-50
115703
COMMERCIAL AUDIO
EQUIPMENT
CAUTION TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD
RECEPTACLE
~120V AC 60Hz
150 W
FUSE 2A
250V
CAUTION DISCONNECT SUPPLY CORD BEFORE CHANGING
CAUTION FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE
ONLY
POWER
PHONES LINE
OUT
RETURN SEND REVERB
REMOTE
32-2046.fm Page 4 Monday, January 24, 2000 12:33 PM