Filter
Top Products
4
Guided Tour - Rear Panel
1: Fan - This variable-speed fan provides vital cooling to your S1500 / S2000 (the hotter the amp gets,
the faster the fan blows!). Make sure that both the front and rear panels are kept free of all obstructions
and that cool, fresh air is accessible at all times. Also, try to ensure that the S1500 / S2000 is used in a
dust-free environment.
2: Circuit Breaker - This circuit breaker will trip if there is a fault with the mains voltage or if maximum
output is exceeded (very highly distorted). Push it in (once only!) to restart the amplifier.
3: AC input - Connect the supplied heavy-gauge 3-pin “IEC” power cable here. Alternatively, the
supplied PowerCon™ connector plate can be attached here.
4: Banana output connectors - Use these to connect each channel of the S1500 / S2000 to 4- or 8-
ohm loudspeakers. Be sure to connect the loudspeaker correctly, with the red (+) terminal normally
connected to the positive input of the speaker and the black (ground) terminal normally connected to the
negative input of the speaker. See page 7 in this manual for more information about Bridged mode and
pages 8 and 9 in this manual for full speaker connection instructions.
5: Speakon™ output connectors - Alternatively, you can use these to connect each channel of the
S1500 / S2000 to 4- or 8-ohm loudspeakers. See page 7 for more information about Bridged mode and
pages 8 and 9 for full Speakon™ connector wiring and interconnection instructions.
6: Bridged / Stereo / Parallel switch - For normal operation, place this three-way switch in its center
(“STEREO”) position. When placed in its right (“PARALLEL”) position, the signal arriving at the
Channel 1 input only is routed to the power amplifiers of both Channel 1 and Channel 2 (the Channel 2
input is ignored), with each power amplifier delivering 750 watts into 4 ohms (in the case of the S1500)
or 1000 watts into 4 ohms (in the case of the S2000). When placed in its left (“BRIDGED”) position, the
signal arriving at the Channel 1 input only is again routed to both power amplifiers (again, the Channel 2
input is ignored), but the two power amplifiers are bridged together, providing 1500 watts of power into
8 ohms (in the case of the S1500) or a full 2000 watts of power into 8 ohms (in the case of the S2000).
For more information, see the “Bridged and Parallel Modes” section on page 7 and the “S1500 / S2000
Connections” section on pages 8 -9.
WARNING: Due to the extremely high power output of the
S1500 / S2000 when used in Bridged mode, be sure to use only loudspeakers sufficiently rated to
handle the resultant wattage (in Bridged mode, these must be 8-ohm speakers).
7: Input connectors
- Connect incoming signal to these electronically balanced Combination
connectors, using either XLR or 1/4" TRS (Tip/Ring/Sleeve) plugs, wired as follows: Pin 2 (or Tip) hot,
Pin 3 (or Ring) cold, and Pin 1 (or Sleeve) ground. We recommend the use of balanced three-conductor
cabling wherever possible (unbalanced two-conductor 1/4" plugs can also be inserted into these inputs,
but you’ll get better signal quality and less outside noise and hum if you use balanced lines).
The S1500 / S2000 accepts input levels of any strength but needs at least 0 dBu to achieve maximum
power. Stereo signals should be connected to both the Channel 1 and Channel 2 input jacks; however,
when operating the S1500 / S2000 in Bridged or Parallel modes, use the Channel 1 input jack only.
See page 7 in this manual for more information about Parallel mode and pages 8 and 9 in this manual
for full interconnection instructions.
8: Link connectors - These XLR connectors provide unity gain outputs, allowing the S1500 / S2000 to
be daisy-chained to additional power amplifiers. Wiring is as follows: Pin 2 hot, Pin 3 cold, Pin 1 ground.
See page 9 in this manual for more information.
BRIDGED PARALLEL
STEREO
BALANCED
0dBm
CH 2 CH 1
BALANCED
0dBm
INPUT
~AC INPUT
115V 60Hz, 1100W
25A/250V
PUSH TO RESET
(4Ω~8Ω) (4Ω~8Ω)
(4Ω~8Ω) (4Ω~8Ω)
CH 2 CH 1
OUTPUT
TRS
BALANCED
TIP=HOT
RING=COLD
SLEEVE=GND
XLR
BALANCED
3=COLD
1=GND
2=HOT
4
2
1
1
7
3
5
6
8
BRIDGED
(8Ω~16Ω)
PUSH
PUSH