Filter
Top Products
50 oz. barium ferrite magnet
HF Driver 1″ compression driver
Mounting Integral 1 3/8″ Pole Mount Receptacle, Fly Points
Dimensions 21 1/4″ (h) x 14 5/8″. (w) x 17 3/8″ (d)
539 mm (h) x 371 mm (w) x 441 mm (d)
Weight 28.5 lbs • 12.9 kg
XP200
Power Rating: 160 Watts LF; 40 Watts HF
Frequency Response 60 Hz – 15 kHz
Sensitivity 97 dB SPL@ 1W/1m
Crossover Frequency 2.3 kHz (12 dB Per Octave Linkwitz-Riley Constant
Phase)
LF Driver 12″ heavy-duty driver
2.5″ voice coil (Kapton Former)
50 oz. barium ferrite magnet
HF Driver 1″ compression driver
Mounting Integral 1 3/8″ Pole Mount Receptacle, Fly Points
Dimensions 21 1/4″ (h) x 14 5/8″. (w) x 17 3/8″ (d)
539 mm (h) x 371 mm (w) x 441 mm (d)
Weight 42.0 lbs • 19.0 kg
XP300
Power Rating: 160 Watts LF; 40 Watts HF
Frequency Response 60 Hz – 15 kHz
Sensitivity 97 dB SPL@ 1W/1m
Crossover Frequency 2.3 kHz (12 dB Per Octave Linkwitz-Riley Constant
Phase)
LF Driver 12″ heavy-duty driver
2.5″ voice coil (Kapton Former)
50 oz. barium ferrite magnet
HF Driver 1″ compression driver
Stereo Mixer Section
Inputs 2 Mic/Line XLR/TRS
1 Stereo Line w/Mic TRS/RCA/XLR
Outputs +4 Balanced XLR
Frequency Response 10 Hz - 50 kHz
Crosstalk 70 dB @ 1 kHz
Equalization Frequencies 100 Hz (Low), 10 kHz (High)
Effects DSP Reverb with 6 Presets
Mounting Integral 1 3/8″ Pole Mount Receptacle, Fly Points
Dimensions 21 1/4″ (h) x 14 5/8″. (w) x 17 3/8″ (d)
539 mm (h) x 371 mm (w) x 441 mm (d)
Weight 45.0 lbs • 20.4 kg
dB500
Power Rating: 500 Watts Program
Frequency Response 60 Hz – 15 kHz ± 3 dB
Sensitivity 97 dB SPL@ 1W/1m
Crossover Frequency 2.3 kHz (24 dB Per Octave)
LF Driver 15″ heavy-duty driver
2.5″ voice coil (Kapton Former)
50 oz. barium ferrite magnet
HF Driver 1.75" titanium compression driver
Mounting Integral 1 3/8″Pole Mount Receptacle
15º wedge monitor position,
30º wedge monitor position, Ten Fly Points
Dimensions 30″ (h) x 19″ (w) x 17″ (d)
762 mm (h) x 483 mm (w) x 432 mm (d)
Weight 53.4 lbs • 24.2 kg
dB500a
Active Power: 400 Watts LF, 100 Watts HF
Frequency Response 60 Hz – 15 kHz ± 3 dB
Sensitivity 97 dB SPL@ 1W/1m
Crossover Frequency 2.3 kHz (24 dB Per Octave)
LF Driver 15″ heavy-duty driver
2.5″ voice coil (Kapton Former)
50 oz. barium ferrite magnet
HF Driver 1.75" titanium compression driver
Mounting Integral 1 3/8″Pole Mount Receptacle
15º wedge monitor position,
30º wedge monitor position, Ten Fly Points
Dimensions 30″ (h) x 19″ (w) x 17″ (d)
762 mm (h) x 483 mm (w) x 432 mm (d)
Weight tbd
EX500
Transducer: 15″ Heavy Duty Driver, 3″ voice coil, aluminum former
Amplifier: High-efficiency tracking converter
Power Rating: 500 Watts RMS
Frequency response 30Hz- 300Hz+/-3 dB
Sensitivity: 94dB SPL @ 1 W/1m
Input Balanced
Connector: XLR - FEMALE
Output Balanced, high-passed tracking low frequency
crossover point
Connector: XLR - MALE
Crossover Frequency: Variable 30Hz – 200Hz
Switch Functions
Stereo /Mono: Selects stereo or mono low frequency oper-
ation
Enclosure
Construction: 3/4" plywood, carpet covered
Finish: Black carpet
Corners: Steel
Casters: Three Inch Heavy Duty
Mounting: Integral 1 3/8" (35mm) Pole Mount
Receptacle,
Dimensions: 20” (h) x 24” (w) x 22.75” (d)
508 mm (h) x 610 mm (w) x 578 mm (d)
Weight: 71 lbs. •
32.25 kg
Microphones
C01
Frequency Response
40~18000 HZ
Polar pattern: Hyper-
cardioid
Element type Back condenser type
Diaphragm thickness 3 microns
Sensitivity -33 dB/Pa
SPL 136 dB
Power supply voltage: phantom power 36V - 52V
Weight 2 lbs. (30.9 kg)
Dimensions 7" (h) x 2.125" (w) x 2.125" (d)
180 mm (h) x 54 mm (w) x 54 mm (d)
Shipping Weight 2.5 lbs.(1.15 Kg)
C02
Frequency Response
TBD
Polar pattern: condenser-
cardioid
Element type condenser
C03
Frequency Response
TBD
Polar pattern: Switchable cardioid, omni,
figure-8
Weight 2 lbs. (30.9 kg)
Dimensions 7" (h) x 2.125" (w) x 2.125" (d)
180 mm (h) x 54 mm (w) x 54 mm (d)
Shipping Weight 2.5 lbs.(1.15 Kg)
C05
Frequency Response
TBD
Polar pattern: condenser-
cardioid
Element type condenser
Q1
Type: Condenser
Polar pattern: Cardioid
Frequency Response: 50 Hz – 20 kHz
Sensitivity: -68dB ±3dB
Max.SPL: 142 dB
Output Impedance (@ 1 kHz): 150 Ω
Connector: 3-pin gold-plated balanced XLR male
Power Requirements: Supply Voltage (Phantom) 11 to 52 Vdc
Dimensions: 7″ • 176 mm overall
Weight: 8.5 oz • 240 g
Q
MIC
Type: Dynamic
Polar pattern: Hypercardioid
Frequency Response: 20 Hz – 18.5 kHz
Sensitivity: -47 dBV @ 94 dB SPL
Max.SPL: 137 dB
Output Impedance (@ 1 kHz): 150 Ω
Connector: 3-pin gold-plated balanced XLR male
Dimensions: 6.75″ • 172 mm overall
Weight: 8.7 oz. • 250 g
Q2
Type: Dynamic
Polar Pattern: Cardioid
Frequency Response: 50 Hz – 15 kHz
Sensitivity: -71 dB ±3 dB
Max. SPL: 137 dB
Output Impedance (@ 1 kHz): 600 Ω (Lo Z)
High Pass Range: -12 dB/octave (HP switch ON)
Attenuation Range: -10 dB/average (ATT switch ON)
Connector: 3-pin gold-plated balanced XLR male
Dimensions: 6″ • 152mm overall
Weight: 10.5 oz. • 300g
Q3
Type: Dynamic
Polar Pattern: Hypercardioid
Frequency Response: 50 Hz – 15 kHz
Sensitivity: -71 dB ±3 dB
Max. SPL: 137 dB
Output Impedance (@ 1 kHz): 600 Ω (Lo Z)
High Pass Range: -12 dB/octave (HP switch ON)
Attenuation Range: -10 dB/average (ATT switch ON)
Connector: 3-pin gold-plated balanced XLR male
Dimensions: 7″ • 178 mm overall
Weight: 15.1 oz. • 431g
Q7
Type: Dynamic
Polar pattern: Cardioid
Connector: 3-pin gold-plated balanced XLR male
Dimensions: 7″ • 177 mm overall
Weight: 13 oz. • 368 g
Q Snare
Type: Dynamic
Polar pattern: Cardioid
Connector: 3-pin gold-plated balanced XLR male
Q Tom
Type: Dynamic
Polar pattern: Cardioid
Connector: 3-pin gold-plated balanced XLR male
Q Kick
Type: Dynamic
Polar pattern: Cardioid
Connector: 3-pin gold-plated balanced XLR male
R11
Type: Dynamic
Polar Pattern: Hypercardioid
Frequency Response: 60 Hz – 18 kHz
Sensitivity: -75 dB ±3 dB
Max. Input Level (1 kHz): 130 dB SPL
Output Impedance (@ 1 kHz): 400 ohm (Lo Z)
Connector: 3-pin XLR male (pin 2 hot)
Dimensions: 6.85″ • 174 mm overall
Weight: 8.8 oz. • 250 g
R21
Type Dynamic
Frequency Response 80 Hz - 12 kHz
Polar Pattern Cardioid
Output Impedance Rated at 500Ω
Sensitivity -53 dBV/pa (1.8 mv/pa)
Connector 3-pin gold plated balanced XLR male
Dimensions
Head length 2.125 in. / 53.97 mm
Main unit length 4.56 in. / 115.88 mm
Total length 6.85 in. / 169.8 mm
Weight 7 oz. / 217 g
R21S
Same as above, with on/off switch
HM40
Type: Condenser
Polar pattern: Cardioid
Connector: 3-pin mini-XLR
S11
Type: Dynamic
Polar pattern: Unidirectional cardioid
Frequency response: 60 Hz – 18 kHz
Sensitivity: -74 dB ±3 dB
Max. input level (1 kHz): 130 dB SPL
Output impedance (@ 1 kHz): 600 Ω ±30%
Connector: 3-pin XLR male
Dimensions: 6.75″ • 172 mm overall
Weight: 8.7 oz. • 250 g
S12
Type: Dynamic
Polar Pattern: Hypercardioid
Frequency Response: 60 Hz – 18 kHz
Sensitivity: -70 dB ±3 dB
Max. Input Level (1 kHz): 130 dB SPL
Output Impedance (@ 1 kHz): 600 Ω ±30%
Connector: 3-pin XLR male
Dimensions: 6.75″ • 172 mm overall
Weight: 8.7 oz. • 250 g
VP1
R21 Microphone same as above
Tripod Mic Stand Heavy-duty Die Cast and Steel
Non-slip Easy Grab Clutch
Over-sized Rubber Feet
Mic Clip with Euro Adapter
Mic Cable
Type XLR-Low Noise High Performance
Length 25′ • 7.62 m
Shipping Weight: 8.5 lbs. • 3.85 kg
Q
E
and Q
V
Generating Element: Back electret cardioid condenser
Polar Pattern
Q
V: Hypercardioid
Q
E (water-resistant): Bi-directional noise cancelling,
pressure gradient type
Mounting system: Adjustable headband and gooseneck
Sensitivity
Q
V:70 mV @ 114 dB SPL
Q
E:80 mV@ 114 dBSPL
Max.SPL: 145 dB
Weight: 1.92 oz. • 54.4 grams
PM4 (For use with QE/QV Headset Mics)
Connectors
Input: TA3M Switchcraft
Output: XLR male
Operating Voltage: 12 Vdc through 48 Vdc
Dimensions
Length: 3.7″ • 93.75mm
Diameter: 0.86″ • 22mm
Weight: 3 oz. • 85 grams
Headphones
RH600
Driver Unit: 40mm Diaphragm Drivers with Neodymium
Magnet
Frequency Unit: 20-22,000 Hz
Impedance: 40ohm ±10%
Sensitivity: 115dB SPL at 1kHz ± 3dB
Input Connector: Gold-Plated Mini Stereo Plug and
1
⁄4
″
Phone Adapter
RH300
Driver Unit: 40mm Diaphragm Drivers with Neodymium
Magnet
Frequency Unit: 20-22,000 Hz
Impedance: 32ohm ±10%
Sensitivity: 106dB SPL at 1kHz ± 3dB
Input Connector: Gold-Plated Mini Stereo Plug and
1
⁄4
″
Phone Adapter
RH100
Driver Unit: 40mm Diaphragm Drivers with Neodymium
Magnet
Frequency Unit: 20-22,000 Hz
Impedance: 64ohm ±10%
Sensitivity: 106dB SPL at 1kHz ± 3dB
Input Connector: Gold-Plated Mini Stereo Plug and
1
⁄4
″
Phone Adapter
PH60
Driver Unit: 34mm Mylar Drivers with An-isotropic Ferrite
Magnet
Frequency Unit: 20-18,000 Hz
Impedance: 32ohm ±10%
Sensitivity: 101dB SPL at 1kHz ± 3dB
Input Connector: Nickel-Plated Mini Stereo Plug and
1
⁄4
″
Phone Adapter
CH700
Closed back design
Driver Unit: 40mm Diaphragm Drivers with Neodymium
Magnet
Frequency Unit: 20 Hz–20 kHz
Impedance: 64ohms
Sensitivity: 108 dB S.P.L. @ 1 kHz ±3dB
Input Connector: Gold-Plated Mini Stereo Plug and
1
⁄4
″
Phone Adapter
CH700
Closed back design
Driver Unit: 40mm Diaphragm Drivers with Neodymium
Magnet
Frequency Unit: 20 Hz–20 kHz
Impedance: 32ohms
Sensitivity: 103 dB S.P.L. @ 1 kHz ±3dB
Input Connector: Gold-Plated Mini Stereo Plug and
1
⁄4
″
Phone Adapter