Samson 4a Speaker User Manual


  Open as PDF
of 72
 
7
MediaOne Series Quick Connections
Note: Before plugging in and turning on, remember the “last on, first off” rule of power
amplifiers (and powered monitors). When powering up your system, be sure that all
the wires are connected, turn your mixer and any other outboard gear on, and then last
turn your MediaOne Series on. When powering down, turn your MediaOne Series off
first and then your mixer and outboard gear.
The MediaOne Series connections can be made via the rear panel RCA Inputs. Follow
the simple steps and diagram below for a quick connection using a standard recording
console’s control room outputs.
• Using the included 20-gauge Extension Speaker cable, connect the Negative
(striped)side of the wire to the Black terminal and the positive side to the Red
terminal on the Right-side monitor.
• Now, connect the Negative (striped) side
of the wire to the Black terminal and the
Positive side to the Red terminal on the
Left-side monitor.
Note: Just about all un-shielded speaker
wire will have a marking indicating the
negative side. To avoid phase cancelation
problems, be sure to maintain the correct
connection for the positive and negative
sides throughout your system.
• Lower your mixer’s master outputs to all
the way off.
• Connect the mixer’s left and right
Control Room outputs to the stereo
input on the Right-side MediaOne
Series.
• Set the MediaOne Series input Volume
control to the 2 o’clock position. NOTE:
If you press the Volume Control, it will
extend out making it easier to adjust.
• Run an audio signal (like some music
from a CD) through your mixer and
raise the Control Room level to a
comfortable listening level.
FROM MIXER'S
CONTROL ROOM
OUTPUTS
2T IN 2T OUT
2T TO MIX
CR MIX
MONO OUT
C/ROOM
+PHONES
5
MIX/2T
RIGHT RIGHT
AUX 2 OUT
LEFT RIGHTLEFT RIGHT
MONO OUT AUX 1 OUT LEFT LEFT
5
0 10
0 10
L RMIXPHONES
CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 CHANNEL 5/6
MIC/LINE 2 MIC/LINE 4 MIC/LINE 5/6 MIC/LINE 7/8
CHANNEL 7/8
R LINE IN R LINE IN
HF
12K
MF
2.5K
15
1010
5
15
5
0
LF
80Hz
0
15
10
5
15
5
0
0
15
1010
55
15
LO CUT
PAN
L R
AUX 1
MON
5
0 10
AUX 2
DSP
5
0 10
L
HF
12K
MF
2.5K
15
1010
5
15
5
0
LF
80Hz
0
15
10
5
15
5
0
0
15
1010
55
15
LO CUT
HF
12K
MF
2.5K
15
1010
5
15
5
0
LF
80Hz
0
15
10
5
15
5
0
0
15
1010
55
15
LO CUT
PAN
R
AUX 1
MON
5
0 10
AUX 2
DSP
5
0 10
PAN
L R
AUX 1
MON
5
0 10
AUX 2
DSP
5
0 10
L
HF
12K
MF
2.5K
15
1010
5
15
5
0
LF
80Hz
0
15
10
5
15
5
0
0
15
1010
55
15
LO CUT
HF
12K
MF
2.5K
15
1010
5
15
5
0
LF
80Hz
0
15
1010
5
15
5
0
0
15
1010
55
15
BAL
AUX 1
MON
AUX 2
DSP
HF
12K
MF
2.5K
15
1010
5
15
5
0
LF
80Hz
0
15
1010
5
15
5
BAL
L R
AUX 1
MON
5
0 10
0
0
15
1010
55
15
AUX 2
DSP
5
0 10
PAN
R
AUX 1
MON
5
0 10
AUX 2
DSP
5
0 10
L R
5
0 10
5
0 10
10
5
0
10
5
20
30
40
10
5
0
10
5
20
30
40
15 15
10
5
0
10
5
20
30
40
10
5
0
10
5
20
30
40
15 15
10
5
0
10
5
20
30
40
10
5
0
10
5
20
30
40
15 15
10
5
0
10
5
20
30
40
10
5
0
10
5
20
30
40
15 15
10
5
0
10
5
20
30
40
10
5
0
10
5
20
30
40
15 15
10
5
0
10
5
20
30
40
10
5
0
10
5
20
30
40
15 15
10
5
0
10
5
20
30
40
10
5
0
10
5
20
30
40
10
5
0
10
5
20
30
40
15
15
15
DIGITAL EFFECTS
MASTER SECTION
MASTER SECTION
5
0 10
30
5
-26
60
+26
GAIN
CLIP
30
5
-26
60
+26
GAIN
CLIP
30
5
-26
60
+26
GAIN
CLIP
30
5
-26
60
+26
GAIN
CLIP
REC
REC
REC REC
REC
REC
MIC/LINE 1 MIC/LINE 3
DIGITAL EFFECTS
DSP
BIT
24
DSP TO MON
SELECT
POWER+48V
PEAK
+6
0
-6
-12
-20
1 LARGE HALL
2 MEDIUM HALL
3 LARGE ROOM
4 VOCAL RM.
5 VOCAL RM. 2
6 CHORUS+REVERB
7 CHORUS+DELAY
8 STAIRWELL
DSP
PEAK
AUX
RET 1
AUX/DSP
RET 2
5
0 10
5
5
0 10
5
0 10
1
2
3 6
7
5
4
8
HARD
DISK
MODE
Connecting the MediaOne Series
Speaker Cable (Un-Shielded)
ENGLISH
 previous next