Russound CA4.4pi Stereo Amplifier User Manual


 
2. Introduction
Congratulations on your recent purchase of the Russound CA4.4pi multi-room controller. This four-zone, four-
source, multi-room controller is an affordable integrated amplifier. The CA4.4pi controller is the heart of the sys-
tem. Four high current stereo power amplifiers are built into the Russound CA4.4pi allowing simple connections
to each speaker in the system. Each zone is operated by an intuitive easy-to-use keypad. The keypad controls all
the functions of the CA4.4pi controller. CA4.4KP keypads have a built-in infra-red receiver used to repeat your
source equipment remote functions back through the CA4.4pi controller.
The Russound CA4.4pi is built with pride. Fidelity, Reliability and Quality is the primary objective. Russound
products are guaranteed to provide years of enjoyment. The CA4.4pi is UL listed and CSA approved for your pro-
tection and peace of mind. Please take a moment to fill out the warranty card and return it to Russound.
3. Possible System Configurations
3
4. Unpacking and Warranty Card
Carefully unpack the CA4.4pi and keep the original carton and
packing materials for future moving, shipment or long-term stor-
age. After opening the box, please check for any visible signs of
damage that were not apparent from the outside of the box. If you
do encounter what appears to be concealed damage, please con-
sult your Russound dealer before proceeding to further unpack or
install the unit.
Make sure to save your sales receipt. Your receipt is extremely
important to establish the duration of your limited Warranty, and
for insurance purposes.
Warranty Card The serial number appears on the rear panel of
this unit near the power cord. Copy the serial number onto your
warranty card and mail it back to Russound / FMP, Inc. 5 Forbes
Road, Newmarket, New Hampshire, 03857, USA. Be sure to
retain a copy and keep it in a safe place.
5. Getting Started
The following information will indicate some tools and materials necessary for a complete installation of the
CA4.4pi:
4 twisted pair communication wire (commonly referred to as CAT 5). This wire will be used to connect the
keypads in each zone to the CA4.4pi controller. 16 Gauge minimum, 2 conductor CL3 rated wire. (Russound
AW162CL3) This wire is used for direct connection between the CA4.4pi and your speakers.
A small jewelers flat-head screwdriver.
A medium sized flat-head screwdriver.
Wire strippers and cutters.
Electric drill and a 1/2" x 6 "drill bit.
A steel-wire fish tape.
Additional tools required to complete installation:
A keyhole saw.
Electrical junction boxes (6).
A stud finder.
A screwdriver (cordless recommended)
Misc. hand tools, nails & screws.
Cable staples.
If you have problems or you are not absolutely comfortable with what you are doing, consult a professional
carpenter, electrician, or system installer.
ZONE 4
Guest Room
ZONE 2
Kitchen
ZONE 3
Library
ZONE 1
Living Room
SOURCE ROOM
Family Room
CASSETTE CD
TUNER
TUNER
CD
CASSETTE
DSS
DSS
(Audio Signal)
CA4.4pi
Controller
Speaker Wire Length Gauge of Speaker Wire
10-50 feet . . . . . . . . . . . . . . . . . . . . . . .18 AWG
50-100 feet . . . . . . . . . . . . . . . . . . . . . .16 AWG
100-150 feet . . . . . . . . . . . . . . . . . . . . .14 AWG
Over 150 feet . . . . . . . . . . . . . . . . . . . .12 AWG
NOTE: CAT5 should not be run more than 100 or
in combination with the CA4.4 LRN. For runs
more than 100 or when using optional CA4.4 LRN
please use 8-conductor 20AWG wire shielded.