Filter
Top Products
120 VAC
50/60 Hz 15 VA
MADE IN U.S.A.
CHANNEL ONE
CHANNEL TWO
OUTPUTS
CAUTION
RISQUE DE CHOC - NE PAS ENLEVER
RISK OF ELECTRIC SHOCK
DO NOT OPEN
MODEL RA235
SERIAL NUMBER
235-
WARNING:
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK.
NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
CHANNEL 2 INPUT
CHANNEL 1 INPUT
S T E R E O
M I X E R
H I F I T U N E R
INTRODUCTION
Thank you for your purchase of the ROLLS RA235 Stereo 35 Watt Power
Amplifier. The RA235 is a virtually indestructible single rack space ampli-
fier intended for musicians and studio owners alike. The unit is ideal for
home studio applications or wherever a clean, efficient, medium wattage
amp is required. Please read the following manual carefully to achieve the
best results from this product.
INSPECTION
1. Unpack and Inspect the RA235 package
Your RA235 was carefully packed at the factory in a protective carton.
Nonetheless, be sure to examine the unit and the carton for any signs of
damage that may have occurred during shipping. If obvious physical
damage is noticed, contact the carrier immediately to make a damage
claim. We suggest saving the shipping carton and packing materials for
safely transporting the unit in the future.
2. Please complete the Warranty Registration Card and return it to the
factory.
DESCRIPTION
FRONT PANEL
VOLUME 1
RA235
PWR
CLIP
CLIP
VOLUME 2
PWR: This LED indicates that the RA235 is receiving power.
VOLUME 1/VOLUME 2: Adjusts the output level of that channel.
CLIP: This LED indicates the channel circuitry is overloading.
REAR PANEL
120 VAC
50/60 Hz 15 VA
MADE IN U.S.A.
CHANNEL ONE
CHANNEL TWO
OUTPUTS
CAUTION
RISQUE DE CHOC - NE PAS ENLEVER
RISK OF ELECTRIC SHOCK
DO NOT OPEN
MODEL RA235
SERIAL NUMBER
235-
WARNING:
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK.
NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
CHANNEL 2 INPUT
CHANNEL 1 INPUT
CHANNEL INPUTS: 1/4" and RCA connectors. Connect the RCA jacks to
the output of a line level device such as a tuner, cassette player, or CD
player.
Note: Do not directly connect the output of a phono player as those
devices require special equalization.
Connect the unbalanced 1/4" jacks to the output of a mixer or preamplifier.
For MONO operation, plug one mono RCA connector between the two
RCA jacks. Either Channel One or Channel Two 1/4" inputs may be used
as the mono input.
INSTALLATION
Mount your RA235 into a safe and sturdy rack. Connect the outputs of
your signal source to the input(s) of the RA235, and connect the outputs
to your speakers. Observe the polarities as indicated in the Rear Panel
descriptions and the diagram below.
THIS DIAGRAM IS A CONNECTION EXAMPLE ONLY. DO NOT USE
BOTH THE RCA AND 1/4" INPUTS AT THE SAME TIME.
Plug the RA235 power cord in to a properly grounded AC power source
and press the Power switch up, so the red part of the switch is showing, to
apply power to the unit.
BURN WARNING! - THE FRONT PANEL OF THE RA235 IS
THE HEAT DISTRIBUTION FOR THE OUTPUT STAGE, IT
WILL VARY BETWEEN 180 TO 200 DEGREES FAHREN-
HEIT.
SCHEMATIC
0
ROLLS CORPORATION
5143 South Main Street
Salt Lake City, Utah84107
0
RA235.SCH
25-Mar-1999
Title
Size: Document Number:
Date:
Rev:
Sheet of
POWER AMPLIFIER RA235
Ba
U1
LM3875
V+
V-
RED
BLK
LM3875
V+
V-
RED
BLK
U21
3
4
7
8
7
4
3
1
V+
V-
CHANNEL 1
CHANNEL 2
8
CLIP
CLIP
J2
PHO NE 1/4
J1A
RCA PC
R4
1K
C6
47U
C3
1U
R1
10K
J1B
RCA PC
J3
PHO NE 1/4
C7
1U
R8
1K
R9
1K
C10
47U
R7
10K
4
1
3
2
BR1
CP8010
SW1
SW SPST
C12
503
C13
503
C4
220P F
C8
220P F
R3
47K
R10
47K
T1
2-00-4880
D1
LDRR
P1
P 100K
P2
P 100K
D2
LDRRR6
1K
R5
10K
D3
LDRR
R12
1K
R11
10K
R13
22K
L1
0.7uH
L2
0.7uH
1
A
HDR2
1
A
HDR2
1
A
HDR2
1
A
HDR2
1 3
2
AC?
AC PLUG
C2
4700U F
C1
4700U F
C5
27P F
C9
27P F
C11
503
R2
1K