Filter
Top Products
Care and Maintenance
Advanced Sound Control
General Controls
General Controls Operating Your Unit Operating Your Unit
Advanced Sound Control Advanced Sound Control
Troubleshooting Tips
Technical Speci cations
Limited Warranty Limited Warranty
Ampli er Section:
RMS Output Power: Dolby Digital Mode with 10% Total Harmonic Distortion
Front, Rear and Center Channel: 167 Watts per channel (1kHz, 8)
Subwoofer Channel: 167 Watts (100Hz, 8)
Total RMS Output Power, Dolby Digital mode: 1000 W
Muting Attenuation: 65 dB
Frequency Response: 200Hz /3dB, 1KHz ref.
Subwoofer Frequency Response: 10Hz/-3dB, 80Hz ref.
Signal to Noise Ratio: 65 dB (Dolby Digital mode)
AM Tuner Section:
Frequency Response: 2kHz +/-6dB, 1kHz ref.
Usable Sensitivity: 800uV/m @ S/N 20dB
Signal to Noise: 38dB
IF Rejection: 35dB
FM Tuner Section:
Frequency Response: 15kHz +/-3dB, 1kHz ref.
Quieting: 24dBu
Signal to Noise: 60dB(stereo) / 65dB(mono)
IF Rejection: 50dB
Dimensions (H x W x D mm) :
Unit: 140 x 430 x 347
Front and Surround Speakers: 200 x 77 x 85
Center Speaker: 85 x 300 x 77
Subwoofer: 360 x 195 x 328.5
Notes:
• CTR stands for Center Speaker selection
while SURR stands for Surround Speaker
selection.
•
By default, the Center and Surround
Speakers
are set to YES. If you decide not to
use them, set the ones you do not intend to
use to NO so that the sound performance is
not a ected.
Tips:
•
When you tune at a weak FM station
manually, press MONO/ST on remote
control
to switch from Stereo to Mono mode.
This
will reduce the background noise.
• If there is any interference, change the
antenna’s position until ideal sound
reception is obtained. TV and other
electronic
devices could be the cause of
interference, so try to position the antenna
away from them.
In the event your product requires repair after the limited warranty period has
expired, please contact our Customer Support Center at 1-877-252-6873 or
www.RCAav.com
Hours: Monday–Thursday: 9am–7pm, Friday: 9am–5pm, Saturday: 9am–NOON Eastern
time.
Important:
You are responsible for any transportation, shipping or insurance relative to the return of product
to our Product Returns Center.
AVC MULTIMEDIA (“AVC”) makes the following limited warranty. This limited warranty extend to the
original consumer purchaser and is limited to non-commercial use of the product.
One Year Parts & Labor Warranty
AVC products purchased in the United States or Canada are warranted to be free from defects in
materials or workmanship for a period of one year from the date of their original retail purchase. If the
unit fails to conform to this warranty, we will service the product using new or refurbished parts and
products, at AVC’s sole discretion.
During a period of one year from the e ective warranty date, AVC will provide, when needed, service labor
to repair a manufacturing defect at its designated Service Center. To obtain warranty service in the United
States or Canada, you must rst call our Customer Support Center at 1-877-252-6873, during the hours
listed in the box below. The determination of service will be made by AVC Customer Support. PLEASE
DO NOT RETURN YOUR UNIT TO AVC WITHOUT PRIOR AUTHORIZATION. New or remanufactured
replacements for defective parts or products will be used for repairs by AVC at its designated Service Center
for one year from the e ective warranty date. Such replacement parts or products are warranted for an
additional one year from the date of repair or replacement. The Customer will be required to ship the unit
to the Service Center indicated at the time Customer Support is contacted to make the necessary repairs.
The customer is responsible for all transportation charges to the service facility.
Packaging and Shipping Instruction
When you send the product to the AVC service facility you must use the original carton box and packing
material or an equivalent as designated by AVC.
LIMITED WARRANTY
Your Responsibility
(1) You must retain the original sale receipt to provide proof of purchase.
(2) These warranties are e ective only if the product is purchased and operated in the United States
or Canada.
(3) Warranties extend only to defects in material or workmanship, and do not extend to any product
or parts which have been lost or discarded, or damage to product or parts caused by misuse,
accident, improper operation or maintenance, or use in violation of instructions provided with
the product, or to product which has been altered or modi ed without authorization of AVC, or
to products or parts thereof which have had the serial number removed or changed.
Out of Warranty
All warranties implied by state law, including the implied warranties of merchantability and tness for
a particular purpose, are expressly limited to the duration of the limited warranties set forth above.
With the exception of any warranties implied by state law as hereby limited, the foregoing warranty
is exclusive and in lieu of all other warranties, guarantees, agreements and similar obligations of
manufacturer or seller with respect to the repair or replacement of any parts. In no event shall AVC be
liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms
of these warranties in any manner whatsoever. The time within action must be commenced to enforce
any obligation of AVC arising under the warranty or under any statute, or law of the United States or
Canada or any state thereof, is hereby limited to one year from the date of purchase. This limitation
does not apply to implied warranties arising under state law.
This warranty gives you speci c legal rights and you may also have other rights, which may vary, from
state to state. Some states do not allow limitation on how long an implied warranty lasts, when an
action may be brought, or the exclusion or limitation of incidental or consequential damages, so the
above provisions may not apply to you.
For more information on other products and services, please visit our web site at
www.RCAav.com
Important: Also keep your “Bill of Sale” as proof of purchase.
Model no. ............................................................................... Product name .........................................................................
Type of set. .........................................................................................................................................................................................
Serial no. ................................................................................. Invoice no. ...............................................................................
Date purchased .................................................................... Dealer name ...........................................................................
FOR SERVICE AND REPAIR, PLEASE VISIT www. RCAav.com
Speci cations and external appearance are subject to change without notice.
Disconnect the audio system from the power source before performing any maintenance.
Cleaning the exterior
Disconnect the system from AC power before cleaning the exterior of the system with a soft dust cloth, or
with a slightly damp leather chamois. Never use strong solvents.
Important Battery Information
• Remove the batteries to avoid leakage if you do not use your remote control for more than one
month.
• Discard leaky batteries immediately as leaking batteries may cause skin burns or other personal
injuries.
• Dispose of batteries in the proper manner, according to provincial and local regulations.
• Any battery may leak electrolyte if mixed with a di erent battery type, if inserted incorrectly, if all
batteries are not replaced at the same time, if disposed of in re, or if an attempt is made to charge a
battery not intended to be recharged.
Safety Precautions
• Never open the cabinet under any circumstances. Any repairs or internal adjustments should be made
only by a trained technician.
• Never operate this product with the cabinet removed.
• Do not touch the player with wet hands. If any liquid enters the player cabinet, take the player to a
trained technician for inspection.
• The apparatus shall not be exposed to dripping and splashing.
• No object lled with liquids, such as vases, shall be placed on the apparatus.
• No naked ame sources such as lighted candles, shall be placed on the apparatus.
Sound Enhancement Systems
This receiver is equipped with several built-in
sound enhancement systems.
Main Unit
Fine Setting of the Components
You can select the surround mode by pressing
SURROUND repeatedly to select among di erent
options. (STEREO, HALL, CHURCH, CLUB, STADIUM,
STUDIO, DOLBY PL EMULATION, DOLBY PL II MUSIC,
DOLBY PL II MOVIE)
The default surround modes for di erent
components are listed in the table below. The unit
will keep the last selection in memory.
Speaker Con gurations
You can also change the setup of the speakers. Use
a subwoofer to enjoy optimum sound.
For optimum surround experience measure the
distance between the speaker and your favorite
listening position. Press DISTANCE to adjust the
speakers’ distance.
1. Press the DISTANCE button to show setup
options.
2. Continue to press the DISTANCE button until
the speaker you want to adjust is displayed.
3. Press / to change the speaker settings. Your
selection will be stored automatically.
4. Repeat step 2 and 3 to set up the next speaker.
You may adjust the distance within the following
ranges:
• Front Speaker distance (FRNT): 0-30ft
• Center Speaker distance (CNTR): 0-30ft
• Rear Speaker distance (SURR): 0-30ft
5. When set up is done, wait for ve seconds to
automatically save your settings or press any
buttons to save your selection and set up
mode.
Factory Default Speaker Distance Settings
• Front Speakers (FRNT): 15ft
• Center Speaker (CNTR): 10t
• Rear Speakers (SURR): 10ft
Unit / AM / FM Operation
ST indicator is o .
• Adjust the antenna.
• Press MONO / ST button to insure you are not outputting in mono.
The signal is Mono. Severe hum or noise.
• The signal is too weak. Connect an external antenna.
• Adjust antenna.
• Reposition antenna away from any electronics.
There is interference to FM reception.
• Turn off other electrical unit (e.g. DVD, CD player) near the unit.
Remote Control Operation
The remote control does not operate the unit.
• No batteries installed (included with your system). Install the batteries before attempting to operate the
remote. Be sure to match the + and - ends of each battery to the symbols shown in the remote battery
compartment.
• The batteries are weak. Replace all batteries.
• The remote is not pointed at the remote control sensor on the main unit or there is an obstacle between
the remote and the main unit.
• The remote control is too far from the main unit, move closer.
General
No audio.
• Make sure the speakers are connected.
• Check the input connections.
• Check the power cord connections.
• Make sure MUTE is off.
• Make sure the digital setting (optical, coaxial or analog) is correct.
• Check that the headphone is not inserted.
No audio from one channel.
• Check the speaker level setting.
• Check the speaker wire or external source cable connections.
Noise occurs when the TV is turned on.
• The TV is too close to the audio system.
Not getting audio from all speakers.
• Check your Surround Mode setting (under Advanced Sound Control section of this book). Your Home
Theater has a number of different SURROUND MODE settings, it defaults to modes most suited to the
type of audio content being played – however you can change these settings. Some of these modes,
(such as DOLBY DIGITAL, and Dolby PROLOGIC II), will cause all speakers to be active, while other modes,
(such as STEREO and 3-STEREO), will cause your rear speakers to be inactive. You can always test your
Home Theater amplifi er - and each speaker, by using the built-in TEST TONE generator (press TEST TONE
button on remote control).
Center / Surround Speaker Setup
1. Press the SETUP button on the remote control
to show setup options.
2. Press
/
until CTR YES or SUR YES is displayed.
3. Press / to select between YES and No.
Home Theater’s Display Dimmer Control
1. Press the SETUP button on the remote control
to show setup options.
2. Press
/
until DIMMER 0 is displayed.
3. Press / to select between 0 and 1.
Fine Setting of the Speakers
All the basic settings have already been pre-set for
the speakers included in the box.
Also, to make the surround sound more e ective
and suit the acoustic conditions in your listening
room, you may need to delay the signal coming
from some of the speakers. Channel delay
compensates for center or surround speakers that
are closer to the listening position than the front
speakers.
Manufactured under license from
Dolby Laboratories.
Dolby, Pro Logic, and the double-D
symbol are trademarks of Dolby
Laboratories.
Dolby Digital
The Dolby Digital mode lets you enjoy full digital
surround from software processed in the Dolby
Digital format. Dolby Digital provides better
sound quality and a more powerful presence
than conventional Dolby Surround. This unit is
equipped with Dolby Digital 5.1-channel so that
you can enjoy enhanced full digital surround
sound. Di erent from Dolby ProLogic in that only
four channels (Front Left, Front Right, Centre and
Rear) are used, the new system provides stereo
separation of the rear speakers (Rear-Right, Rear-
Left). Adding the subwoofer channel to the 5
channels for bass sounds (counted as 0.1 channel)
results in 5.1 channels (or 6 Channels) input Dolby
Digital for that bring you the most sophisticated
sound enjoyment.
Dolby Pro Logic II
The Pro Logic II mode uses the built-in circuit to
steer the Left, Center, Right and Surround left
and right channel audio signals and uses all ve
speakers to play both stereo and Dolby Pro Logic
program source, such as TV and VCR.
Dolby Pro Logic II includes Dolby Pro Logic II
Movie, Dolby Pro Logic II Music and Dolby Pro
Logic Emulation.
You can use this mode with any stereo program
source (such as VCR/TV) to enjoy multi-channel
sound experience.
1. ON/STANDBY
Turns on / o the unit. When the unit is turned
on, the unit will go to the mode it was in before
powered o .
2.
/ (TUNING buttons)
Tunes in to desired stations in AM/FM mode.
3.
/ (PRESET buttons)
Selects preset stations in AM/FM mode.
4. GAME jacks
Connect game consoles or other AV products that
have AUX audio outputs.
5. LINE IN
Connect portable audio devices or other AV
products that have a LINE-OUT jack.
6.
/ (SURROUND buttons)
Selects among digital sound processors. (STEREO,
HALL, CHURCH, CLUB, STADIUM, STUDIO, DOLBY
PL EMULATION, DOLBY PL II MUSIC, DOLBY PL II
MOVIE)
7. DVD, TV, SAT-CAB, AM/FM, VCR, BD and
GAME/LINE-IN (SOURCE buttons)
Selects sound source.
8. Headphone jack
9. MASTER VOLUME
Adjusts the volume.
10. SUBWOOFER
Selects among subwoofer output levels. (SOFT
SUBWOOFER, BALANCE SUBWOOFER, STRONG
SUBWOOFER, POWERFUL SUBWOOFER)
Remote Control
Install two “AAA” batteries in the remote control
prior to use.
1. ON•OFF
Turn on/o the unit.
2. SLEEP
Selects sleep time.
3. NIGHT
Selects among night mode options (DRC OFF,
SOFT and ON) which compresses the volume
di erence between normal voices and sounds
such as explosions. (Available only during Dolby
digital signal playback)
4. TEST TONE
Speaker test tone setting. Refer to “Advanced
Sound Control” for details.
5. SURROUND
Selects digital sound processors. (STEREO, HALL,
CHURCH, CLUB, STADIUM, STUDIO, DOLBY PL
EMULATION, DOLBY PL II MUSIC, DOLBY PL II
MOVIE)
6. DISTANCE
Adjusts the speakers’ listening distance.
7.
/ / /
• Press / to select among setting items in Setup
mode.
• Press
/ to adjust the values when the display
shows the setup you want to change.
• Press OK to con rm your selection.
8. LEVEL
Speaker level setting. Refer to “Advanced Sound
Control” for details.
Selecting Source
When one of the SOURCE buttons on the front
panel or on the remote control is pressed, the
corresponding input will be activated.
The unit acts as a switching device between all the
sources that are plugged into it.
Example 1:
If you have connected a DVD player to the DVD
jack on the unit, press DVD on the front panel
or on the remote control to receive the sounds
transmitted by the DVD.
Example 2:
If a VCR is connected to the VCR jack of the unit,
press VCR on the front panel or on the remote
control, the sound from the VCR will be selected.
You can connect up to 7 audio sources to this
ampli er:
Example: Connecting a Blu-ray Player
1. Connect the optical digital audio out jack of Blu-
ray player to OPTICAL 2 jack on the rear panel of
the unit.
2. Press ON/STANDBY on the front panel of the
unit or press ON•OFF on the remote control to
switch on the unit.
3. Press BD on the main unit or remote control to
select the DVD source.
4. Switch ON the Blu-ray player and start playback.
5. Set the sound mode if needed (see “Advanced
Sound Control” for details).
Example: Connecting a TV to a digital
input
1. If TV has an OPT output, connect it to the
OPTICAL 1 jack on the rear panel of the unit.
2. Press ON•OFF on the remote control to switch
on the unit.
3. Press TV button to select TV mode.
4. Press the SETUP button to show setup options.
5. Press / until ANALOG, OPTICAL 1, OPTICAL 2
or COAXIAL is displayed.
6.
Press / to select among ANALOG / OPTICAL 1
/
OPTICAL
2 / COAXIAL to match your connection
(OPTICAL1). Your selection will be stored for future
use automatically.
7.
Switch on the TV.
RADIO
The unit has a built-in tuner that allows for AM/FM
radio function.
Connect the FM antenna and the AM loop antenna
at the back of the unit. Rotate the AM loop for
better reception.
Automatic Tuning
1. Press AM/FM.
2. Press and hold TUNER+ or TUNER- button on
the remote control or
or button on the
front panel of the unit until the auto searching
starts. Searching stops when the system tunes in
a station. (Once the FM station that broadcasts
Stereo sound is found, STEREO is displayed.)
3. Repeat step 2 to tune to another radio station.
4. To prematurely stop the searching function,
press TUNER+ or TUNER- button on the remote
control.
5.
Adjusting the volume by pressing VOL +/ VOL -.
Manual Tuning
Press TUNER+ or TUNER- button on the remote
control or
or button on the front panel of the
unit repeatedly to tune a desired frequency.
Automatic Preset Programming
The unit can preset 30 FM stations and 30 AM
stations. Before tuning, make sure to turn down
the volume to minimum.
1. Press AM/FM to enter the AM/FM mode.
2. Press and hold AM/FM for two seconds to start
automatic preset programming.
3. Radio frequencies will be browsed and radio
stations stored automatically. When all the
available radio stations are stored or all 60 preset
stations (30 for AM and 30 for FM) memory
locations are full, the auto preset programming
function will stop.
Manual Preset
1. Press AM/FM to select the desired radio mode.
2. Press and hold TUNER+/TUNER- button on the
remote control or
/ button on the front
panel of the unit until the system tunes in a
station.
3. Press MEMORY. While the Program Preset
number is still ashing, input your desired
preset number using the numeric buttons, then
press MEMORY to store it.
Select Preset Stations
1. Press AM/FM to enter the Tuner mode with
selecting AM or FM band.
2. Press
/ on the main unit repeatedly or
directly press MEM + / MEM - button on the
remote control to search for the preset stations.
Each time you press the button, the system
tunes in one preset station.
GAME
1. Connects audio out jacks of the
TV game to the
GAME jacks on the front panel
of the unit.
2. Press the GAME/LINE-IN button on the front
panel repeatedly to select GAME mode.
LINEIN
1. Connects one end of the 3.5mm stereo cable
(not included) to the LINEIN connector on the
front panel of the unit and the other to the line
out or headphone jack on an external source.
2. Press GAME/LINE-IN on the front panel to
select LINE-IN mode.
SETTING THE SLEEP TIMER
You can set the system to turn o at a preset time,
so you can fall asleep listening to music. You can
preset the time in 30-minutes increments.
1. Press SLEEP button on the remote control.
2. Each time you press SLEEP, the minutes display
(the remaining time) changes by 30 minutes.
3. When you set the sleep timer, "SLEEP" icon will
be shown on the front panel display.
• To change the remaining time, press SLEEP
repeatedly to select the desired time.
• To clear the preset sleep time, press the SLEEP
button until SLP OFF appears.
Stereo
The Stereo mode uses the two main channel
outputs from the front speakers and subwoofer
speaker. Use this mode if you have connected the
front speakers only.
DSP (Digital Sound Processor)
These digital sound e ects resemble sounds in a
real environment such as (STEREO, HALL, CHURCH,
CLUB, STADIUM, STUDIO, DOLBY PL EMULATION,
DOLBY PL II MUSIC, DOLBY PL II MOVIE). DSP
automatically converts analog audio signals to
digital ones which enables you to adjust the sound
without degrading the sound quality. Di erent
modes will give you di erent feels of size and types
of listening environment.
Dynamic Bass Ampli ed System (dBas)
With “Dynamic Bass Ampli ed System“ (dBas),
the discrete ampli er is located in the unit so the
subwoofer keeps the power needed to reproduce
powerful e ects. Four settings are available: SOFT,
BALANCE, STRONG and POWERFUL.
Press SUBWOOFER to select the subwoofer (dBas)
e ects level according to your needs.
Front Left Speaker
Front Right Speaker
Center Speaker
Rear Right Speaker
Rear Left Speaker
Listening
Zone
Front Left
Speaker
Front Right
Speaker
Subwoofer
Center Speaker
Rear Left
Speaker
Rear Right
Speaker
Front Left Speaker
Front Right Speaker
Listening
Zone
Front Left
Speaker
Front Right
Speaker
Subwoofer
Digital Inputs
The Home Theater has three digital audio inputs
for DVD, SAT/CAB, BD, TV or GAME sources.
The default input for DVD is the Coaxial Digital
input, while the default inputs for SAT-CAB and
BD are the Optical 1 and Optical 2 Digital Input
respectively. However, if you need to assign a
source to a di erent input:
1.
Select the source (DVD, SAT/CAB, BD, TV or GAME).
2. Press the SETUP button to show setup options.
3. Press / until OPTICAL 1, OPTICAL 2 or COAXIAL
is displayed.
4.
Press / to select among OPTICAL 1/ OPTICAL 2 /
COAXIAL to match your connection. Your selection
will be stored for future use automatically.
Select this setting to play digital signals from a
DVD, SAT/CAB, BD, TV or GAME source.
Analog Inputs
The Home Theater has three analog audio inputs:
TV, VCR, GAME and LINE-IN.
Note:
To play Dolby Prologic II Movie sound, press the
SURROUND buttons until “Dolby PL II MOVIE”
appears on the Display.
To play Dolby Digital sound, the source must be
connected to the unit via the optical or coaxial
terminal.
If digital input
(optical or coaxial)
is selected
Dolby Digital
If analog input is
selected
N/A
Source Input
DVD
Pro Logic II Movie
T
V
Dolby Digital N/ASAT-CAB
AM/FM StereoAM/FM
N/A Pro Logic II MovieVCR
Dolby Digital
Dolby Digital
Dolby Digital
N/ABD
Pro Logic II Movie
GAME
Pro Logic II Music
N/ALINE-IN
Default input
Coaxial (DVD: COAX)
Built-in tuner
Analog (VCR)
Analog
Source
DVD
Analog (TV: ANL)
T
V
Optical1 (SA T: OPT1)SAT-CAB
AM/FM
VCR
Optical2 (BD: OPT2)BD
GAME
AnalogLINE-IN
(GAME: ANL)
(LINE-IN)
Testing and Adjusting Speaker Loudness
The TEST TONE button on the remote control
allows
you to adjust each speaker volume level
individually
to suit your particular listening
environment.
1. Press the TEST TONE button.
2. A tone will be heard at each speaker, one speaker
at a time.
3. Press the
/ button on the remote control to
adjust the level of the speaker that is playing
the tone at the particular moment. The Home
Theater’s display will also indicate which speaker
is playing the tone at any particular moment.
4. Press Exit button to exit this mode.
Adjusting Speaker Loudness Without Using
Test Tones
1. To adjust individual speaker volume level, press
LEVEL on the remote control.
2. Continue to press LEVEL on the remote control
to select the speaker to be adjusted, then press
the
/ buttons to adjust the level.
3. Press Exit button to exit this mode.
R/S
L/S
Rch
Cch
Lch
Front
Left
Rear
Right
Rear
Left
Front
Right
Center
1
2
3
8
7654
9
10
GAME
GAME
BD
13
14
15
16
17
18
20
19
21
1
2
3
4
5
6
7
8
9
10
11
12
TV VCR DVD SAT/CAB
AM/FM GAME/LINE-IN
SOURCE
SOURCE buttons
on remote
control
DVD
Corresponding
connector at the
rear panel
DVD
LINE- IN & GAME jacks
on the front panel
SOURCE
buttons on
front panel
DVD
TV TVTV
SAT/CAB SAT/CABSAT-CAB
AM/FM built-inAM/FM
VCR VCRVCR
GAME/LINE-IN GAME/LINE-IN
BD BD BD
The source name you selected will be shown on
the display.
Notes:
• Your unit has a built-in tuner. Just connect the
appropriate antenna to the back of the unit
and you will be able to listen to radio stations.
(For details, please refer to Radio section)
• Connections at the back panel can be
interchanged depending on whether sources
have the same audio input.
9. SUBWOOFER
Selects among subwoofer sound levels. (SOFT
SUBWOOFER, BALANCE SUBWOOFER, STRONG
SUBWOOFER, POWERFUL SUBWOOFER)
10. MEM + / MEM -
Selects programmed stations in AM/FM mode.
11. TUNER +
Press to turn up the radio frequency in AM/FM
mode.
12. EQ buttons
Selects among preset equalizer mode (POP, FLAT,
JAZZ, CLASSIC, ROCK, BASS and TREBLE). Press the
corresponding button to select the desired sound
mode. This function is only available in Stereo mode.
13. Number buttons
Directly accesses a preset station in AM/FM mode.
14. MEMORY
Stores stations as preset stations in AM/FM mode.
15. MONO/ST
Selects between Stereo and Mono sound in FM
mode.
16. SETUP
Enters Setup mode. Use
/ to select among setup
options.
17. MUTE
Mutes all sound.
18. VOL + / VOL -
Adjusts the volume.
19. EXIT
Exits the current setting.
20. TUNER -
Press to turn down the radio frequency in AM/FM
mode.
21. Source buttons
Selects audio sources.
- 13 -- 12 -- 11 - - 14 -
- 17 -- 16 -- 15 - - 18 -
- 21 -- 20 -- 19 - - 22 -
Need more help?
Please visit online help at
http://www.RCAav.com