Filter
Top Products
EN
Repeating/Intro scan
You can replay the entire CD or one
track as many times as you wish as well
as listen to the beginning of each track for
10 seconds.
Press MODE successively to
1. Replay the entire CD .
2. Replay the current track.
3. Play the beginning of each track
for 10 seconds.
(The number of the track being played will
be displayed and SCAN will appear.)
4. Press again to the function de-
select.
Program
This function lets you listen to the tracks
you
selected in the order you want. The CD
player must be in Stop mode.
1. Press P button. P will appear in the dis-
play.
2. Select the track to store by pressing
& press P again to confirm.
3. Return to step 2 to store other tracks.
4. Press PLAY/PAUSE button to listen to
your programming.
Note : To prevent excessive battery
consumption, the unit switches off
automatically in all modes after 30s if
no key has been activated.
You can program up to 24 tracks.
To play your program again, press play.
To add/edit tracks to the program, go to
stop mode ; press and hold P button
again. Refer to step 2 of the above
paragraph.
Press P to turn program mode on, then
press PLAY/PAUSE and to check the
program.
To cancel your program, press and hold
the mode key when you are in the stop
mode. ERASE will appear in the display.
The program will be automatically
canceled.
To exit program mode, remove P from the
display by pressing STOP then P.
6
THE CD PLAYER
or
Listening to a Compact Disc
1. Slide the OPEN switch to the right
to open the door. Insert a disc and
press lightly on the centre to lock. Close
the door. Press PLAY/PAUSE button. Rd
DISC will appear in the display. Then,
the total number of tracks
and time of the CD will
be displayed. If the
disc compartment
is empty or the
disc cannot be
played, No Disc
will appear in
the display.
2. You can also
change tracks or
quickly listen to
part of a track by
pressing down or
holding
.3. Slide CONTROL switch to
HOLD position to lock the button to
avoid accidental activation of unwanted
functions.
Listening to a CD in your car
(For RP2425 / RP2427 only)
1. Select a power source (either
battery power or the car DC adaptor)
2. Insert the cassette adaptor into the
tape deck and plug the cord into the
CD player’s HEADPHONES jack.
3 . Insert a compact disc and press PLAY/
PAUSE button. Adjust CD player’s volume
to a mid level (make sure the Bass Boost is
turned off).
4. Use the car stereo to adjust vol-
ume, tone . Adjust the vol-
ume of your CD player
for better volume
control.
5. Before ejecting
the cassette after
you have finished
listening, make
sure the car
stereo’s volume is
turned down.
The ELECTRONIC
SHOCK PROTECTION*
system prevents
sound interruptions
when impacts or
vibrations occur.
Electronic anti-
shock consumes less
power and increases the battery life.
Therefore, the ESPX function is always
ON.
After many successive impacts, the buffer
might be emptied causing a brief sound
interruption for the memory to reload.
The buffer is 45 seconds long.
5
or
b
a
s
s
b
o
o
s
t
m
o
d
e
P
4
5
s
e
c
o
n
d
a
d
v
a
n
c
e
d
s
k
i
p
p
r
o
t
e
c
t
i
o
n
•
r
e
m
o
t
e
c
o
n
t
r
o
l
c
d
p
l
a
y
e
r
45
CD-R / RW COMPATIBLE
p
r
o
g
•
d
i
s
p
l
a
y
s
e
c
o
n
d
tr
ac
k
minute
• 1 bit d/a convertor •
bass boost
esp x
P
1
2
1
EN
45
THE CD PLAYER
2_RP2420 EN 6/21/01 11:58 AM Page 8