Filter
Top Products
LISTEN TO iPOD/iPHONE WITH DOCKING CONNECTOR
Warning : Turn off your iPod or iPhone before docking on the unit
1. Press the ‘POWER/AL OFF’ button to turn on the unit.
2. Press the ‘FUNC/CL.ADJ’ button to select the iPod mode.
3. Turn the ADJUSTABLE DOCK DIAL to the depth that fit your iPod/iPhone best.
4. Connect the iPod or iPhone to the docking connector, the iPod or iPhone will start playing.
5. Press the ‘VOL+’ or ‘VOL-‘ button to your desired listening level.
6. During playing or in pause mode, press the ‘SKIP+/TUNE+’ button to go to the next track.
7. During playing, press the ‘SKIP-/TUNE-‘ button once to go back to the beginning of the track.
Press the ‘SKIP-/TUNE-‘ button twice to go back to the previous track.
8. In pause mode, press the ‘SKIP-/TUNE-‘ button once to go back to the previous track.
9. Press the ‘PLAY/PAUSE/SYNC’ button to temporarily pause playing. To resume, press the
‘PLAY/PAUSE/SYNC’ button again.
Operates the IPod/iPhone with the Remote Control
MENU Button – Use this button to go to the Menu Page of the iPod or iPhone.
UP Button – Use this button to scroll up the selection in the Menu.
DN Button – Use this button to scroll down the selection in the Menu.
ENTER Button – Use this button to confirm the selection.
PLAY/PAUSE Button – Use this button to pause playing or resume playing.
STOP Button – Use this button to stop playing.
SKIP-/TUNE- Button – Use this button to go back to the beginning of the track or to the previous
track.
SKIP+/TUNE+ Button – Use this button to go to the next track.
Warning : Please make sure that your iPod or iPhone is properly docked into the unit. Failure to
do so may damage your iPod.
Charging your iPod
While your iPod or iPhone is docked in the unit and the unit is connected to AC power, your iPod
or iPhone will recharge until your iPod or iPhone is fully charged.
AUX-IN CONNECTION
1. Press the ‘POWER/AL OFF’ button to turn on the unit.
2. Press the ‘FUNC/CL.ADJ.’ button to select the AUX mode.
3. Insert one side of the audio cable into the Line-Out or Phone Jack on your MP3 Player or
audio device and the other side into the AUX-IN jack of the unit.
4. Turn on your MP3 player or audio device and follow its playback instructions.
MUTE FUNCTION
This function can only operate by remote control.
Press the MUTE button on the remote control to mute the unit, press the MUTE button again to
cancel the function.
- 8 -
SLEEP TO MUSIC FUNCTION
1. This function can only operate by remote control.
2. This function allows you to listen to the radio, iPhone/iPod or CD while you fall asleep.
3. Press the ‘SLEEP/SNOOZE’ button on the remote control, the display will show the default sleep
time of 90 minutes. Press the ‘SLEEP/SNOOZE’ button again to select the sleep time with
decrement of 10 minutes.
4. When the correct sleep time is selected, stop pressing the ‘SLEEP/SNOOZE’ button, the unit will go
to the sleep mode in about 5 seconds with SLEEP appear in the display.
5. Now you can enjoy listening to the selected music for the pre-set period of sleep time.
6. After this pre-set time has elapsed, the unit will switch off automatically.
REMOTE CONTROL OPERATION
Take off the plastic sheet located at the battery compartment tray to activate the remote control.
Point the remote control at the remote sensor on the main unit and press the function button to activate
the function.
1. POWER/AL.OFF Button 12. AL2 Button
2. MENU Button 13. PROGRAM Button
3. PLAY/PAUSE/SYNC Button 14. P-MODE/MONO Button
4. STOP Button 15. SLEEP/SNOOZE Button
5. ENTER Button 16. MUTE Button
6. SKIP+/TUNE+ Button 17. VOLUME - Button
7. SKIP-/TUNE- Button 18. VOLUME + Button
8. FUNC./CL.ADJ Button 19. MEMORY - Button
9. UP Button 20. MEMORY + Button
10. DOWN Button 21. MEM Button
11. AL1 Button
- 9 -