PYLE Audio PBT30M Headphones User Manual


  Open as PDF
of 2
 
Reminding:
- For safety reason, please don't leave the headset in car alone when charging.
- When the battery is low, the LED will not turn on until the headset is charged up, which may
take several minutes.
● Led Status
10
9
128
7
LED
1 x 3 sec. Blue
1 x 1 sec. Blue
Blinking red
Red LED on
Red LED off
Red/Blue Blinking
Status
Ready can be accessed by paired devices
Talking
Battery low (max. 15 Minutes left)
Under charging
Fully charged
Pairing-Mode
PBT30M
11
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
FCC ID:NV6-CS8127
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1)This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
USB Dongle and PBT30M Bluetooth Headset
Voice Over Internet Protocol (VoIP) Application
Install Software for Bluetooth USB Dongle from the CD-ROM provided in the USB Dongle
package. Note that the CD-ROM is not available in the PBT30M package.
Plug the USB Bluetooth Dongle (purchased separately) into the USB socket of a PC.
Download from the corresponding websites and install Skype, MSN messenger,Netmeeting,
Yahoo messenger, or ICQ application software in the PC.
Pairing: Put the PBT30M Bluetooth Headset into "pairing" mode. Start the Bluetooth software
and pair the USB Dongle with the PBT30M Headset. The Headset passkey is "0000".
Connecting and Disconnecting: To connect the USB dongle, press the S1 key on the Headset.
To disconnect the Bluetooth link, press the S1 key again.After turn off and turn on the headset,
you just need to press S1 key to establish the audio link with USB dongle if the USB dongle
is the last used device.
Testing the Bluetooth Link: After the USB Dongle is connect with the PBT30M Headset, the PC
audio will be automatically routed to the "Bluetooth Audio" driver. Play some music on the PC
by Windows Media Player or other music applications; you should be able to hear the music
on the Headset. If you can't hear it, then go the "control Panel " ->" Sound and Audio Device
Properties"-> "Audio"-> "Sound playback" select the "Bluetooth Audio" to activate the link.
Now you can start using the VoIP application and talk to your friend through your Headset
wirelessly and freely.
Connecting PBT30M Bluetooth Headset back to your Bluetooth mobile phone. Please follow
the steps from 'Headset in Pairing Mode' to 'Establishing Bluetooth Link'.
The following company is responsible for this declaration:
Sound Around Inc.
1600 63rd Street
Brooklyn N.Y. 11204,
USA
Phone: 1-800-444-5671 718-535-1800
Fax: 718-236-2400
Bluetooth Qualified Design ID: B013218
Sound Around Inc.
Environmental
friendly
Note
Material: 80g Woodfree Paper
1
2
3
4
5
6
7
8
A
B
C
D
E
A
B
C
E
1
2
3
4
5
6
7
8
D
PART NO.:
MCB-8127020-1A
MODEL:
8127
DRAWN:
Limingzan
DATE:
20071204
PAPER SIZE:
A3
UNIT:
MM
SCALE:
1:1
DESCRIPTION:
#User Manual For PYLE Logo
In-Tech Electronics Ltd.
 previous