Filter
Top Products
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE OPERATING EQUIPMENT
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves,or other apparatus
(including amplifiers) that produce heat.
9. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, liquid has been spilled or
objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
10. WARNING: To reduce the risk of fire or electric shock,
this apparatus should not be exposed to rain or
moisture and objects filled with liquids, such as
vases, should not be placed on this apparatus.
Product Disposal—Certain international, national
and/or local laws and/or regulations may apply
regarding the disposal of this product. For further
detailed information, please contact the retailer
where you purchased this product or the Polk Audio
Importer/Distributor in your country. A listing of
Polk Audio Importer/Distributors can be found on
the Polk Audio website www.polkaudio.com or
by contacting Polk Audio at 5601 Metro Drive,
Baltimore, Maryland 21215, USA—
Phone: +1 410 358-3600.
WARNING: LISTEN CAREFULLY
Polk Audio loudspeakers and subwoofers are capable
of playing at extremely high volume levels, which
could cause serious or permanent hearing damage.
Polk Audio, Inc. accepts no liability for hearing loss,
bodily injury or property damage resulting from the
misuse of its products.
Keep these guidelines in mind and always use your
own good judgment when controlling volume:
• You should limit prolonged exposure to volumes
that exceed 85 decibels(dB).
For more about safe volume levels, go to www.polkaudio.com/
education/article/SPL/, or refer to the Occupational Health
and Safety Administration (OSHA) guidelines at
http://www.osha.gov/dts/osta/otm/noise/standards_more.html
TAKE INVENTORY
Inside each speaker container,
you should find the following:
1. One RTS
C or one set of RTSFX speakers
2. Speaker mounting template (RTS
FX only)
3. Paint mask
4. One perforated aluminum grille (for each speaker)
5. One cloth grille (for each speaker)
6. One RTS
C/RTSFX Manual
7. Registration Card
8. STL105 Stud-Lock Bracket (RTS
FX only)
9. Enclosure (RTS
C only)
Important Note: If anything is missing or damaged,
or if your speaker fails to operate, notify Polk Audio
Customer Support Services immediately at
800-377-7655.
INSTALLATION RECOMMENDATION
FOR OPTIMUM PERFORMANCE
Important Note: RTS Series Loudspeakers are not
magnetically shielded and should not be placed closer
than 1' (30cm) from a direct-view television or video
monitor.
Important Note: You should have a thorough under-
standing of and adhere to all local building and fire
codes. Also, you should be familiar with the area
behind the wall or ceiling into which you plan to
install your speakers. Always use wire that meets
appropriate building and fire codes. Use at least
14 gauge wire or heavier for the best sound quality.
(Note: Wiring is best performed by an experienced
professional.)
When installing your RTS Series In wall Loudspeakers,
be aware of the weight of your particular model (see
specification page for the weight of your model) and
the sturdiness of the material into which you are
installing the speaker. Be aware of any concealed
studs, electrical wiring or plumbing in the wall or ceil-
ing into which you are installing the speakers.
If you doubt that you possess the necessary skills or
tools, consult your Polk Audio dealer or a professional
installer.
WIRE RECOMMENDATIONS
Runs Gauge
Lengths up to 25' 18 or 16
Lengths greater than 25' 16 or 14
but less than 50'
Lengths greater than 50' 14 or 12
but less than 75'
Lengths greater than 75' 12
LOUDSPEAKER INSTALLATION
You will need:
• Pencil for marking the location
of installation.
• Keyhole saw, utility knife or material-appropriate
tool for cutting drywall or other wall material.
• Level.
• Screwdriver, preferably powered,
with Phillips Head bit.
• Power drill with appropriate bit
(optional, for starting wall cut).
Stud-Lock Mounting System
™
(RTSFX only)
Installation
See the instructions included with each Stud-Lock
Mounting System
™
.
Important Note: For new construction: If you are using
a pre-construction bracket, always install it first before
installing the Stud-Lock Mounting System
™
.
If you are installing a pre-construction bracket (PB105)
and a Stud-Lock Mounting System (STL105) together,
be aware that the speaker’s enclosure can catch on
the edge of the pre-construction bracket. Push the
bottom of the loudspeaker enclosure up and over the
protruding edge of the pre-construction bracket.
This will fully seat the loudspeaker in the wall.
Trace around
the template.
Cut the hole with
the appropriate tool.
2 Polk Audio Customer Service: 1-800-377-7655 (Outside US & Canada: 410-358-3600) Monday-Friday, 9:00 AM-6:00 PM EST, polkcs@polkaudio.com
RTSFX