10 © 2010 Polk Audio—all rights reserved © 2010 Polk Audio—all rights reserved 11
Speaker Wiring Diagram PA330
The Polk Audio PA330 amplifier offers two positive and two negative output terminals for ease of
connecting the speakers to the amplifier. Each amplifier is stable to 2 Ohm per channel or 4 Ohm bridged.
Tri-mode
For Tri-mode wiring the high frequency speakers should be run in stereo
>`ÊÕÃiÊ>Ê«>ÃÃÛiÊÊiÊVÀÃÃÛiÀÊV>«>VÌÀ®ÊÜÌÊi>VÊÌÊÀiÛiÊÌiÊ
low frequency. The mono low frequency speaker would be connected
in the bridge mode to the two stereo channels with a in line passive
VÀÃÃÛiÀÊ`ÕVÌÀ®ÊÌÊÀiÛiÊÌiÊ}ÊvÀiµÕiViðÊ/iÊ}ÊvÀiµÕiVÞÊ
speakers should be no less than 2 Ohm and the low frequency speaker
should be no less than 4 Ohm.
Bridging
For bridging into a single speaker load, the Polk Audio PA330
has the ability to bridge the front or rear channels together.
The impedance of the speaker must not be less than 4 Ohm.
Speaker Wiring Diagram PA660
/iÊ*ÊÕ`Ê*ÈÈäÊ>«viÀÊvviÀÃÊÌÜÊÃiÌÃÊvÀÌÊ>`ÊÀi>À®ÊvÊÌÜÊ«ÃÌÛiÊ>`ÊÌÜÊi}>ÌÛiÊÕÌ«ÕÌÊÌiÀ>ÃÊvÀÊi>ÃiÊ
of connecting the speakers to the amplifier. Each amplifier is stable to 2 Ohm per channel or 4 Ohm per bridged channel pair.
Tri-mode
For Tri-mode wiring the high frequency speakers should be run
ÊÃÌiÀiÊ>`ÊÕÃiÊ>Ê«>ÃÃÛiÊÊiÊVÀÃÃÛiÀÊV>«>VÌÀ®ÊÜÌÊ
each to remove the low frequency. The mono low frequency
speaker would be connected in the bridge mode to the two
ÃÌiÀiÊV>iÃÊÜÌÊ>ÊÊiÊ«>ÃÃÛiÊVÀÃÃÛiÀÊ`ÕVÌÀ®ÊÌÊ
remove the high frequencies. The high frequency speakers
ÃÕ`ÊLiÊÊiÃÃÊÌ>ÊÓÊ"Ê>`ÊÌiÊÜÊvÀiµÕiVÞÊLÀ`}i`®Ê
speaker should be no less than 4 Ohm.
Bridging
For bridging into a single speaker load, the Polk Audio PA660
has the ability to bridge the front or rear channels together.
The impedance of the speaker must not be less than 4 Ohm.
Bridged Stereo
4
24
24
Bridged
Tri-mode
24
24
4
bridged
bridged
4 4
24
24
24
24
Front and Rear
in Tri-mode
4 channel
24
24 24
24
2 channels
Bridged Front & Rear
bridged bridged
48 48