Filter
Top Products
Controls and displays
05
33
En
English
Français
Deutsch
Nederlands
Italiano
Español
EFFECT/CH SEL
Press repeatedly to select a channel, then
use
LEVEL +/–
to adjust the level
(see
Tip
on page 50). Also adjusts the level of the
Advanced Surround effects (page 35) as
well as Dolby Pro Logic IIx Music (page 36)
and Neo:6 Music parameters (page 36).
You can then use the
LEVEL +/–
buttons to
make these adjustments.
LEVEL +/–
Use to adjust the effect and channel levels,
as well as to change Dolby Pro Logic IIx
and Neo:6 Music parameter settings.
10 SHIFT
Press to access the DVR controls (above the
component control buttons) as well as some
RECEIVER
controls.
11
SOURCE
Press to turn on/off other components
connected to the receiver (see page 55 for
more on this).
12 Character display (LCD)
This display shows information when
transmitting control signals.
The following commands are shown when
you’re setting the remote to control other
components (see
Controlling the rest of your
system
on page 55):
SETUP
Indicates the setup mode, from which you
choose the options below.
PRESET
See
Selecting preset codes directly
on
page 55.
LEARN
See
Programming signals from other
remote controls
on page 56.
DIRECT F
See
Direct function
on page 57.
ERASE
See
Erasing one of the remote control
button settings
on page 57.
RESET
See
Erasing all of the remote control presets
on page 57.
READ ID
See
Confirming preset codes
on page 58.
13 RECEIVER
Switches the remote to control the receiver
(used to select the green commands above the
number buttons (
FL DIMMER
, etc). Also use
this button to set up surround sound (page 11,
page 43).
14 VOL +/–
Use to set the listening volume.
15 MUTE
Mutes the sound or restores the sound if it has
been muted (adjusting the volume also
restores the sound).
Operating range of remote control
unit
The remote control may not work properly if:
• There are obstacles between the remote
control and the receiver's remote sensor.
• Direct sunlight or fluorescent light is
shining onto the remote sensor.
• The receiver is located near a device that is
emitting infrared rays.
• The receiver is operated simultaneously
with another infrared remote control unit.
S
-
V
I
D
E
O
V
I
D
E
O
U
P
D
O
W
N
M
U
L
T
I
J
O
G
M
A
S
TE
R
V
O
L
U
M
E
E
N
T
E
R
A
U
D
IO
/
V
ID
E
O
M
UL
T
I
-
C
H
A
N
N
E
L
A
M
P
L
I
F
IER
V
S
X
-
9
1
5
STAND
B
Y
/
O
N
PH
O
N
E
S
D
V
D
/
L
D
T
V
/
SAT
D
V
R/V
C
R
V
I
D
E
O
C
D
C
D-
R
/T
A
P
E
/
M
D
T
U
N
E
R
AU
X
ST
A
ND
A
R
D
A
C
O
U
ST
I
C
E
Q
A
D
V
A
N
C
E
D
S
U
R
R
S
T
/
D
I
R
E
C
T
/A
U
T
O
S
U
R
R
S
IG
N
A
L
S
E
L
E
C
T
LI
S
T
E
N
I
N
G
M
O
D
E
Q
U
I
C
K
S
E
T
UP
SYS
T
E
M
S
E
T
U
P
R
ET
UR
N
S
PE
A
K
E
R
S
B
A
N
D
T
ON
E
I
N
P
U
T
A
T
T
E
X
T
E
N
D
E
D
M
O
D
E
T
U
N
I
N
G
/
S
T
AT
I
O
N
T
U
N
E
R
E
D
I
T
F
L
D
I
M
M
E
R
30
30
23 ft (7m)
VSX_815-915.book.fm 33 ページ ２００４年１２月８日 水曜日 午後４時３分