Filter
Top Products
22
English
point 2
Clock/Timer
View clock
The clock (if it is set) will be shown in Standby
mode.
To view the clock in any source mode
(VCD or TUNER for example)
● Press CLOCK.
➜ The clock will be displayed for a few seconds.
➜ If the clock has not been set, "24 HOUR" or
"12 HOUR" will start flashing.
Clock setting
The clock can be set in either 12- or 24-hour
mode, for example "AM 12:00" or "00:00".
1 Press CLOCK to select clock mode.
2 Press PROGRAM to select clock setting mode.
➜ "24 HOUR" or "12 HOUR" will start flashing.
3 Press
S
or
T
to select 12- and 24- hour
mode.
4 Press PROGRAM to confirm the selection.
➜ The hour indication will start flashing.
5 Press
S
or
T
to set the hours.
6 Press PROGRAM to confirm the selection.
➜ The minutes indication will start flashing.
7 Press
S
or
T
to set the minutes.
8 Press PROGRAM to store the setting
➜ The clock will start working.
● To exit without storing the setting, press Ç on
the system.
Notes:
– The clock setting will be erased when the power
cord is disconnected or if a power failure occurred.
– During clock setting, if no button is pressed
within 5 seconds, the system will exit clock setting
mode automatically.
CLOCK
TIMER
ON/OFF
SET
OPEN/
CLOSE
STEREO/
VOCAL
OSD/DIM
iR SENSOR
SHUFFLE REV.MODE
BAND
RECORD
PROGRAM
MIC
REPEAT• DEMO STOP•CLEAR SEARCH•TUNING
VOLUME
STANDBY
ON
MC
-
55 VIDEO CD MICRO SYSTEM
DIGITAL SOUND
CONTROL
4 PRESET 3
DIRECTION PLAY•PAUSE
1
2
3
VCD
TUNER TAPE
Timer setting
The system can switch on to VCD, TUNER or
TAPE mode automatically at a preset time,
serving as an alarm to wake you up.
IMPORTANT!
– Before setting the timer, ensure that the
clock is set correctly.
– The timer can only be activated from
Standby mode.
1 Press and hold TIMER ON/OFF (SET) on
the system or TIMER on the remote control for
more than 2 seconds to select timer setting
mode.
➜ TIMER will appear on the display.
● Press
S
or
T
repeatedly to view the
previous setting.
2 Press PROGRAM to change the previous
setting or start a new setting.
➜ "TUNER", "TAPE", "CD" or "REC TU" will start
flashing.
3 Press
S
or
T
to select the desired source.
4 Press PROGRAM to confirm the selection.
● If "TUNER" or "REC TU" is selected, press
TUNER to select the current radio station or
press
S
or
T
to select a desired preset
radio station and press PROGRAM to confirm
the selection.
➜ "VOL" and the volume level will start flashing.
5 Press
S
or
T
to set the volume level.
6 Press PROGRAM to confirm the setting.
➜ ON and the hour indication will start flashing.
7 Set the time to start playback.
Press
S
or
T
to set timer start hours and
press PROGRAM to store the setting and
repeat the same procedure to set the minutes.
➜ OFF and the hour indication will start flashing.
8 Set the time to stop playback following the
above procedure.
➜ "TIMER OK" will be display briefly and the
timer is now set.
9 Switch the system to standby mode.
● When reached the preset timer, the selected
source will play if the timer has been activated.
pg 001-026/MC55/21-Eng 6/8/01, 1:41 PM22