Filter
Top Products
3
7
8
9
2
DVD VIDEO DIGITAL SURROUND SYSTEM
OPEN/CLOSE
SOURCEPROGRAM
STOP
P
R
E
V
N
E
X
T
VOLUME
STANDBY
ON
PROGRESSIVE SCAN
P
L
A
Y
/
P
A
U
S
E
AV 4
480P
4,5
N
ISSAN
6
1
PLAYING A
DVD DISC
T
o play a DVD disc using the home cinema player/receiver, fol-
low these steps:
NOTE: Your Philips player/receiver remote can operate your
Philips TV.
1
Load the batteries (supplied) in the player/receiver
remote. Open the battery bay door. Place the batteries in
the battery bay as marked (aligned +, –). Then close the
battery bay door.
2
Point the player/receiver remote toward the TV and
press the TV/AV button repeatedly until “AV4 480P”
appears on the screen. “TV/AV” will show on the
player/receiver display.
3
Point the player/receiver remote toward the
player/receiver and press DISC to put the player/receiver
in DISC mode. (If a disc is already in the player/receiver,
“DISC” will appear briefly on the player/receiver display.)
4
To place your favorite movie on the tray, press the
OPEN/CLOSE button on the player/receiver. The DVD
tray will eject and “OPEN” will show on the
player/receiver display. With the printed side up, place
your disc on the tray.
5
Press the OPEN/CLOSE button on the player/receiver
again to retract the DVD tray. “CLOSE” and then
“LOADING” will show briefly on the player/receiver dis-
play.
6
Watch for the selection screen (the Title or Disc menu)
to appear on the TV. The illustration shown on this page
is for example purposes only; screen layout and content
will vary according to the DVD disc.
7
To move around in the selection screen, point the play-
er/receiver remote at the player/receiver and use the “
:,
;, o,p” buttons to highlight the desired selection.
8
With the item you desire selected, press the
PLAY/PAUSE “BF””” button on the remote to begin play-
ing.
9
To stop playing the disc, press the STOP“
CC
” button on
the player/receiver remote.
NOTE: If the player/receiver won’t react to the remote, press
the DISC button again, then press the “BF, ;, :, o,p” buttons
as mentioned in the steps above to perform the desired action.
Playable Discs
This home-cinema player/receiver will play the following types of Discs: pre-
recorded audio CDs, finalized audio CDR and audio CDRW discs, VCDs,
Super VCDs and DVDs, and MP3-CDs (CD-ROMs with MP3 tracks).
Region Codes
DVDs must be labeled for ALL regions or for Region 1 in order to
play on this Home Cinema system. You cannot play Discs that are
labeled for other regions. If one of these logos appears on your DVD
or its case, it should play on this DVD Player.
1
LISTENING TO TV BROADCASTS THROUGH YOUR
HOME CINEMA SYSTEM
Y
ou can also enjoy surround sound with TV broadcasts. Follow
the steps below for connections and setup.
1
Point the player/receiver remote toward the player
receiver and press the TV/AV button to put the receiver in
Philips TV mode.
2
Point the player receiver remote toward the TV and
press the “H” or “G” buttons to select the desired chan-
nel.
Set your TV volume to a “FIXED” output mode. This will allow
you to control the volume output using the player/receiver
remote.
3
Point the TV remote toward the TV and press the
MENU/SELECT button to show the onscreen menu.
4
Press the CURSOR RING DOWN once to highlight
SOUND.
5
Press the CURSOR RING RIGHT to enter the SOUND
submenu.
6
Press the CURSOR RING DOWN repeatedly until
AUDIO OUT is highlighted.
7
If AUDIO OUT is set to VARIABLE, press the CURSOR
RING LEFT or RIGHT to select FIXED.
8
Press the STATUS/EXIT button to exit the menu.
NOTE: Although the receiver will still provide sound for
the TV broadcast if you do not perform steps 3–8 above,
following the steps is suggested. Otherwise, you must
adjust the TV volume to balance the sound input to the
receiver so as to avoid distortion.
9
After following steps 3–8 above, adjust your TV volume
to “0.” This is suggested because sound coming from the
TV’s speakers would interfere the surround-sound effect
provided by the home cinema system.
NOTE: When you don’t want to use the receiver for
sound, all you need to do is turn up the TV volume.
Point the player/receiver remote toward the
player/receiver and press the VOL + or – buttons to adjust
the home cinema surround sound to the desired level.
10
10
STEREO
2
1
2
2
10
PICTURE
SOUND
FEATURES
INSTALL
TREBLE
BASS
BALANCE
AVL
INCR
.
SURROUND
TREBLE 30
BASS
BALANCE
AVL
INCR
.
SURROUND
SOUND
SOUND
INCR
.
SURROUND
HEADPHONE
STEREO
SAP
AUDIO OUT VARIABLE
SOUND
INCR
.
SURROUND
HEADPHONE
STEREO
SAP
AUDIO OUT FIXED
SOUND
INCR
.
SURROUND
HEADPHONE
STEREO
SAP
AUDIO OUT FIXED
VOLUME 0
PICTURE
SOUND
FEATURES
INSTALL
BRIGHTNESS
COLOR
PICTURE
SHARPNESS
TINT
PIP
213
546
879
0
TV
SWAP PIP CH
DN
UP
FREEZE
SOUND
MUTE
SURF
A/CH
POWER
PICTURE
STATUS/
EXIT
POSITION
VCR
ACC
MENU/
SELECT
VOL
CH
TV/VCR
ACTIVE
CONTROL
3
4,6
5
7
8
9
Buttons on Your Player/Receiver Remote
that You Can Use to Operate Your TV
Power
ON/OFF
Numbers
for Channel
Selection
Channel Up
Volume Up
or Down
TV/AV
for Philips
TV Mode
Channel
Down
• If the TV broadcast is in mono mode, the rear speakers will not
have sound, regardless of the receiver setting (MATRIX or
STEREO). This is normal.
• See the user manual for the LX3500D DVD Video Digital
Surround System for instructions for tuning and listening to radio
stations.
HELPFUL HINTS
NOTE: Use the SOURCE buttons
on the player/receiver remote to
select the desired source: TV/AV,
DISC, TUNER, or AUX.
Quick Use
Guide
Quick Use
Guide
Push
Lift
2
NOTES:
• To change the player/receiver
remote to Philips TV mode,
you must first press the
TV/AV button. Pressing any
of the other source buttons
(DISC, TUNER, or AUX)
will take the remote out of
Philips TV mode.
• You can select TV input
sources by pointing the play-
er/receiver remote toward the
TV and pressing the TV/AV
button. Each press of the but-
ton selects a different input
source—AV1, CVI, AV2,
AV3, AV4, AV5, and TV
channel.