Filter
Top Products
17
English
Selecting a desired track
Selecting a desired track when
playback is stopped
1 Press PREV í or NEXT ë until the
desired track appears on the display.
2 Press PLAY É to start playback.
™ The selected track number and
elapsed playing time appear on the
display.
Selecting a desired track during
playback
• Press PREV í or NEXT ë until the
desired track appears on the display.
™ The selected track number and
elapsed playing time appear on the
display.
• If you press PREV í once it will skip
to the beginning of the current track and
play the track again.
Searching for a particular
passage during playback
• Press and hold à or á until the
desired passage is located.
™ The volume will be reduced.
• Play returns to normal when à or á
is released.
Programming Tracks
Programming tracks of a loaded CD is
possible when playback is stopped. The
display will indicate the total tracks stored
in the program. Up to 40 tracks can be
stored in the memory in any order. When
40 tracks are stored and you attempt to
store another track, the display will show
“FULL”.
1 Load the desired discs in the disc trays.
2 Press PROGRAM to start programming.
™ The
PROGRAM flag starts flashing.
™ It will cancel any previously selected
repeat mode.
3 Press the CD (CD 1•2•3) button to
select the disc.
4 Press PREV í or NEXT ë to select
the desired track.
5 Press PROGRAM to store the track.
• Repeat steps
3
to
5
to store other discs
and tracks.
6 Press STOP•CLEAR Ç once to end
programming.
™ The total number of tracks
programmed and total playing time
appear on the display.
Notes:
– If the total playing time is more than
“
99:59
” or if one of the programmed
tracks has a number greater than 30,
then “
--:--
” appears on the display
instead of the total playing time.
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Reviewing the program
Reviewing of the program is possible only
when playback is stopped.
• Press PREV í or NEXT ë repeatedly
to review the programmed tracks.
• Press STOP•CLEAR Ç to exit review
mode.
Playing the program
1 Press PLAY É to start program
playback.
™ “PLAY PROGRAM” appears on
the display.
™ The track number and elapsed
playing time of the current track will
appear on the display.
• If you press REPEAT during program
playback, the current track will be
played repeatedly.
™ The
REPEAT and PROGRAM flags will be
displayed.
2 Press STOP•CLEAR Ç to stop
program playback.
Notes:
– If you press any of the CD DIRECT PLAY
buttons, the system will play the
selected disc or track and the stored
program will be ignored temporarily. The
PROGRAM flag also will disappear
temporarily from the display. It will
CD
reappear when playback of the selected
disc ends.
– REPEAT DISC mode will be cancelled
when program playback begins.
Erasing the program
(when
playback is stopped)
• Press STOP•CLEAR Ç.
™ “PROGRAM CLEARED” will be
displayed.
Note:
– The program will be erased when the
system is disconnected from the power
supply or when the CD carousel is
opened. If the CD carousel is opened,
the tracks belonging to the outer two
trays will be erased and the display will
show “
TRACKS CLEARED
”.
Shuffle
(only on remote control)
In shuffle mode, the system plays all the
available discs and their tracks in random
order. Shuffle may be used also when
tracks are programmed.
To shuffle all the discs and tracks
1 Press SHUFFLE.
™ “SHUFFLE” will be displayed.
™ The
SHUFFLE flag, the disc and the
track selected at random appear on
the display.
• The discs and the tracks will be played
in random order until you press
STOP•CLEAR Ç.