Phase Technology PC-SUB WL-12 Speaker User Manual


  Open as PDF
of 3
 
An MSE Audio Group company www.mseaudio.com
Phase Technology 8650 College Boulevard Overland Park, Kansas 66210 (866) 663-9770 www.phasetech.com
LINE
IN
LOPASS
FREQ.Hz.
GAIN
MIN. MAX.
PHASE
180°
0°
POWER
CAUTION:
FORCONTINUEDPROTECTION
AGAINST RISK OF FIRE,
REPLACE ONLY WITH SAME
TYPE FUSE AND RATING.
ATTENTION:
UTILISERUNFUSIBLEDE
RECHANGE DE MEME
TYPE ET CALIBRE.
ON
120V60Hz3A
T3.15AL250V
240V50Hz1.5A
T1.6AL250V
Filename:300WLsilkRevB.cdr
1Color:Gold
SCIP/N:SLK2793
Rev:B
RESET
STATUS
WIRELESS
40
LFE
200
80
120
PC-SUB WL Subwoofer Amplier Panel
(on back of subwoofer)
1
2
3
4
6
5
7
PC-SUB WL SERIES AMPLIFIER PANEL
1. Power/Auto ON/OFF: When this switch is left “ON”, the subwoofer
automatically activates upon detection of an audio signal; the subwoofer
goes into “STANDBY” after approximately ten (10) minutes of silence. The
LED on the amplier will change from Red to Green when an input signal is
detected and the amplier turns on.
2. Power Input: Connects to a standard AC power outlet with the supplied
power cord. The PC-SUB WL is designed to adjust automatically to handle
power sources of 100-240V, 50-60Hz. Please be certain that the proper
fuse is installed on the amp for the input voltage used locally (see ratings
on amplier panel).
3. Wireless Signal: Blue LED light is on when wireless signal is being received.
Press RESET to establish or re-establish a wireless connection. (See
wireless set up instructions)
4. Line In: FOR WIRED CONNECTION ONLY: Using a high-quality RCA cable,
connect the “SUB OUT” terminal on your receiver or processor to the “LINE
IN” terminal on your PC-SUB WL subwoofer. (See wired setup connection
instructions.)
5. Low-Pass Frequency Control: If using the crossover setting in your A/V
receiver or processor, set this control to “LFE” (Low-Frequency Effects). If
using the sub’s internal crossover, choose the setting that sounds best and
matches the low-frequency cutoff of your main speakers. It may take some
experimentation to nd the best sound for your room and your equipment.
6. Phase Control: This adjustment matches the phase - the in and out movement of speaker cones - to that of your main speakers. Adjust
this control by listening to music with bass content. The setting is correct when the bass sounds the fullest.
7. Gain Control: This adjustment increases or decreases the power, and thus volume, of the PC-SUB WL. As with the Phase Control and
the Low-Pass Frequency Control, it may take some experimentation to nd the best sound for your system.
VIBRATION ISOLATION PADS
Included with your PC-SUB WL are a set of four (4) gray disks with an adhesive backing. The Vibration Isolation Pads should be used
whenever your subwoofer is installed on any hard ooring surface. These pads prevent the subwoofer from moving against the oor when
played at high levels. To use the pads, simply peel off the paper backing from the four disks and apply one pad to the bottom of each of
the rubber feet of the subwoofer.
Specications
Woofer
Passive Radiator
Magnet Assembly
Wireless
Amplier Power (Watts, continuous)
Amplier Power (Watts, peak)
Frequency Response (-6 dB)
Low Pass Crossover
Dimensions*
Finish
Shipping Weight
PC-SUB WL-8
8” ultra long-throw mica graphite poly
cone with NBR surround
8” ultra long-throw mica graphite poly
cone with NBR surround
12 lbs.
2.4 GHz uncompressed audio
streaming
300
900
28-200 Hz (LFE)
40-200 Hz (variable) 24 dB/octave
11 3/16” W x 12 1/8” H x 12 5/8” D
High-gloss Black or Satin Cherry
33 lbs.
PC-SUB WL-10
10” ultra long-throw mica graphite poly
cone with NBR surround
10” ultra long-throw mica graphite poly
cone with NBR surround
12 lbs.
2.4 GHz uncompressed audio
streaming
300
900
24-200 Hz (LFE)
40-200 Hz (variable) 24 dB/octave
13” W x 13 3/8” H x 14 1/2” D
High-gloss Black or Satin Cherry
38 lbs.
PC-SUB WL-12
12” ultra long-throw mica graphite poly
cone with NBR surround
12” ultra long-throw mica graphite poly
cone with NBR surround
12 lbs.
2.4 GHz uncompressed audio
streaming
300
900
22-200 Hz (LFE)
40-200 Hz (variable) 24 dB/octave
15 7/16” W x 16 1/4” H x 16 7/16” D
High-gloss Black or Satin Cherry
47 lbs.
*add 1” to depth for connecting cables
 previous