Filter
Top Products
4
• FULL RANGE: This switch position transforms the P200 amplifier in to a high performance 20Hz-20kHz,
200-watt mono-block power amplifier. With the switch in this position the front panel Crossover control and
the rear panel Low Frequency Equalization control do not function.
4. LINE IN connectors are a set of dual RCA type plugs that accept an input signal from the subwoofer or main signal
outputs from your home theater receiver or control center. Either one or both of the inputs can be used as required. The
left and right input signals are summed together in the amplifier to provide it with a mono input signal.
5. LOW FREQUENCY EQ control adjusts the bass contour of the amplifier and subwoofer to allow the optimization of the
subwoofer performance compensating for variations in room acoustics and installation locations. This control provides an
adjustment range of –3dB to +6 dB centered around 30 Hz.
6. TRIGGER INPUT is provided for remote control switching of the auto-on circuit of the P200 amplifier. A positive 12V
trigger signal applied to the tip of a 3.5mm mini plug inserted into this connector activates the amplifier. When the voltage
drops to 0 the amplifier will turn off. This input overrides the automatic music sensing circuit in the amplifier. The
automatic music sensor activates when it senses that an audio signal is present at the LINE IN connectors and after 3-4
seconds turns on the amplifier. When the input signal is removed the amplifier will go turn off after about 10 minuets.
7. A/C power line voltage selector is used to properly matching the line voltage of your wall outlet to the P200 amplifier.
For the USA and Canada this switch is set to the 110-120V position. For other countries the customer should check with
his retailer for the proper setting and line cord requirements.
8. The power line cord socket is for the connection of the main power cord from your wall outlet to the amplifier. In the
USA and Canada the amplifier is supplied with a standard IEC polarized power cord.
9. The power socket also contains the main power fuse for the P200 amplifier. Should the amplifier fail to operate unplug
the amplifier from the wall outlet and remove the power cord from the rear of the amplifier. Remove the fuse cover
located under the power cord socket by prying up on it with a small screwdriver and check the main power fuse. If the
fuse is blown there is a spare fuse in the cover that can be used to replace the blown fuse. Replace the main power
fuse with only the size and current specified on the rear of the amplifier per you’re A/C input voltage
requirements.
SPECIFICATIONS
AMPLIFIER POWER 200 WATTS CONTINUOUS LESS THEN .1% THD @ 4 OHMS, 350 WATTS PEAK
150 WATTS CONTINUOUS LESS THEN .1% THD @ 8 OHMS, 215 WATTS PEAK
CROSSOVER FREQUENCY 40-160 HZ ADJUSTABLE @ 24 DB/OCTAVE LOW PASS
LFE FREQUENCY
RESPONSE
20-500 Hz
FULL RANGE RESPONSE 10Hz-40kHz + 1 dB
INPUT SENSITIVITY 150 mV FOR FULL OUTPUT
LOW FREQUENCY EQ -3dB to +6dB @ 30 Hz
DIMENSIONS 17.75”W x 1.875”H x 11.75”D
WEIGHT 18 LBS
Limited Warranty
Phase Technology warrants its loudspeakers to be free from defects in material and workmanship for a period of ten (10) years for speaker
product and three (3) years for the electronic components to the original purchaser. Purchase must be made from an authorized Phase
Technology dealer.
This warranty does not cover service or parts to repair damage caused by misuse, abuse, damage while in transit, alterations,
unauthorized repairs, failure to follow instructions, fire, flood or any other cause beyond the reasonable control of Phase Technology.
Defects in speaker cabinets or grilles must be brought to the attention of your dealer immediately after purchase. This warranty will be void
if the products’ serial number has been altered or removed.
To obtain warranty service, defective product must be shipped in its original carton or equivalent together with original invoice or bill of sale,
insured and prepaid to your authorized Phase Technology dealer or the factory when warranty service is requested.
If you choose to return the defective product to the factory you must first call us at (904) 777-0700 to obtain a Return Authorization number
prior to shipping. Product repaired under this warranty will be returned to you freight collect.
Implied Warranties
Phase Technology will not pay for loss of time, inconvenience, loss of use, or property damage caused by your speaker product or its
failure to work, or any other incidental or consequential damages. Some states do not allow the exclusion or limitation of consequential
damages, so the above limitation may not apply to you.
PHASE TECHNOLOGY CORPORATION
6400 YOUNGERMAN CIRCLE
JACKSONVILLE, FL 32244
1-888-PHASETK
www.phasetech.com 218-2029