Filter
Top Products
RQT7114
18
Advanced operations
Playing from memory
Storing to the CUE PADS and playing
Before use
•Switch [PLAY SELECT] to select the media to be used
•Turn [MODE] on the rear panel to TURNTABLE
•Insert the SD Memory Card or CD to be used
You can store cue points to CUE PADS and immediately replay one
of those points by inserting the media and simply pressing the appro-
priate pad.
Storing to the CUE PADS in real-time
1. During play or while paused, press [REALTIME REC]
•All SAMPLE PADS, CUE PADS 1-4 pad lamps and CUE lamp
flash.
•Press [REALTIME REC] again to cancel.
2. At the desired point, press one of the [CUE PADS 1-4]
•The play point selected is stored in memory. The previously stored
data is erased if it exists.
•The selected pad lamp lights.
•The CUE PADS data for each CD or SD Memory Card is stored to
memory, and the setting is restored once the set media is re-in-
serted.
Store desired points to memory and
play (loop play)
During media play you can set any 2 desired points to loop play.
Creating a loop
1. During play, press LOOP [IN] at the desired point
•LOOP IN lamp lights.
•Press LOOP [IN] again to set again.
•After pressing LOOP [IN] you can cancel settings by pressing
[EXIT/RELOOP].
To set in real time
Press LOOP [IN] to set the desired point
To set manually
1. Stop the platter slip surface at the desired point
2. Press LOOP [IN]
To set using the cue point transferred from memory
1. Select the cue bank and back cue
2. Press LOOP [IN]
2. During play press LOOP [OUT]
Repeat step 1 above to set.
•The LOOP OUT and IN lamp flashes, and play begins looping
between the loop in point and the loop out point.
•Turn off Auto Cue before setting or playing a loop beyond a track.
•When setting the loop setting again, perform the above steps after
canceling loop play by pressing [EXIT/RELOOP].
•You can also control the platter slip surface and make tempo ad-
justments etc. during loop play.
•During loop play, looping is released when you have exceeded the
loop range using the skip or search button.
•The loop points for each CD or SD Memory Card are stored to
memory, and the settings are restored once the set media is re-
inserted.
Loop release (Cancel)
During loop play, press [EXIT/RELOOP]
•Play continues without returning to loop play even when the loop
out point is reached.
•The LOOP IN, OUT lamps change to stationary lights.
Re-loop (Returns to a loop)
After releasing a loop, press [EXIT/RELOOP] during play
•Returns to the loop in point previously set and begins loop play
again.
When using CD-R, CD-RW MP3 files
•When you reverse play while using cue point, cue pad or re-loop,
reverse play is not effective beyond the set starting point.
Play from the stored point
Play after back cueing
After performing back cue, press [PLAY/PAUSE]
•Play begins from the set point.
Correcting the cue point
1. Perform back cue
2. Perform steps 2-4 in the Setting the cue point at any
point section again. (
page 17)
•A new cue point is stored to memory.
Playing from the CUE PADS
Press one of the lit [CUE PADS 1-4]
•Even if you are playing, play immediately begins from the point
stored to the CUE PADS .
When paused in the TURNTABLE mode, the platter begins to
turn and play.
•During play of the CUE PADS, if you press the same pad again,
play will repeat from the beginning of the memorized point.
•During play of the CUE PADS, if you press a different pad, play
will switch to the selected pad.
Stopping cue pad play
Press [PLAY/PAUSE]
•The PLAY/PAUSE lamp flashes and play pauses.