Filter
Top Products
7
RQT9801
Getting Started
How you set up your speakers can affect the bass and the sound field.
Note the following points:
≥Place speakers on flat secure bases.
≥Keep your speakers at least 10 mm away from the system for proper
ventilation.
≥Placing speakers too close to floors, walls, and corners can result in
excessive bass. Cover walls and windows with thick curtains.
≥For optional wall mount, refer to page 19.
Setup example (“Surround layout (Recommended)”: Standard
surround placement)
Place the front, center, and surround speakers at approximately the same
distance from the seating position. The angles in the diagram are
approximate.
§1 Position with at least 5 cm of space on all sides for proper ventilation.
§2 Put on a rack or shelf. Vibration caused by the speaker can disrupt
the picture if it is placed directly on the TV.
§3 Place to the right or left of the TV, on the floor or a sturdy shelf so that
it will not cause vibration. Leave about 30 cm from the TV.
Depending on the room layout, you may like to use all the speakers at the
front (“Front layout (Alternative)”) (B 9, Easy setup).
Notes on speaker use
≥Use only supplied speakers
Using other speakers can damage the unit, and sound quality will be
negatively affected.
≥You can damage your speakers and shorten their useful life if you play
sound at high levels over extended periods.
≥Reduce the volume in the following cases to avoid damage:
– When playing distorted sound.
– When the speakers are reverberating due to a record player, noise
from FM broadcasts, or continuous signals from an oscillator, test
disc, or electronic instrument.
– When adjusting the sound quality.
– When turning the unit on or off.
≥These speakers do not have magnetic shielding. Do not place them
near a TV, PC, or other device that is affected by magnetic fields.
≥Keep magnetized items away. Magnetized cards, watches, etc., can be
damaged if placed too close to the speaker.
Turn off all equipment before connection and read the appropriate
operating instructions.
Do not connect the AC mains lead until all other
connections are completed.
Use of the speaker cable stickers is convenient when making cable
connections.
Connect the speaker cables to the appropriate speakers by referring to
the above table.
Insert the wire fully, taking care not to insert beyond the wire insulation.
Be careful not to cross (short circuit) or reverse the polarity of the
speaker wires as doing so may damage the speakers.
step 2 Positioning
Caution
≥The main unit and supplied speakers are to be used only as
indicated in this setup. Failure to do so may lead to damage to
the amplifier and/or the speakers, and may result in the risk of
fire. Consult a qualified service person if damage has occurred
or if you experience a sudden change in performance.
≥Do not attempt to attach these speakers to walls using methods
other than those described in this manual.
120°
60°
Center speaker
§2
Front speaker
(left)
Subwoofer
§3
Surround
speaker (left)
Surround
speaker (right)
Front speaker
(right)
Main unit
§1
step 3 Connections
1
Speaker connections
Cable type Speakers
(Attached to
subwoofer)
Subwoofer 6
SUBWOOFER /
ENCEINTE
D’EXTRÊMES-
GRAVES
Short Center speaker 5 CENTER / CENTRE
[XH160] (Supplied
with the speaker
stand)
[XH100] [XH60]
Short
Front speaker (R) 2
FRONT /
AVANT
Front speaker (L) 1
Long
Surround speaker (R) 4
SURROUND /
AMBIOPHONIESurround speaker (L) 3
Verify the type of speaker with the
label on the speaker before connecting
the appropriate cable.
SURROUND
Lch
SURROUND
SURROUND
SURROUND
Lch
e.g., Surround speaker (L)
Speaker cable
stickers
Long cable
e.g.
FRONTFRONT
SURROUNDSURROUND
L
R
L
R
3
6
5
2
1
4
3
5
5
5
SUBWOOFERSUBWOOFER
CENTERCENTER
Main unit (rear)
White
Blue
line
White
Blue line
Push!
Surround
speaker (L)
Push!
i: White
j: Blue line
SC-XH160-100-60_GAGSGW_RQT9801-B_eng.book 7 ページ ２０１２年１２月２６日 水曜日 午後４時５７分