Filter
Top Products
11
RQT9729
ENGLISH
Stations cannot be selected.
Change the FM frequency step.
1 Press [RADIO] to select “FM”.
2 Press and hold [RADIO] on the unit.
After a few seconds the display changes to show the
current lowest frequency. Continue to hold the button
down. The lowest frequency changes and the step is
changed.
Cannot charge or operate.
≥ Have you selected the appropriate selector?
Press [iPod] to select either “IPOD_DOCK” or
“IPOD_PORT”.
≥ Check that the iPod/iPhone/iPad is connected properly.
(l 6)
≥ The battery of the iPod/iPhone/iPad is depleted. Charge
the iPod/iPhone/iPad, and then operate again.
≥ Connect the iPod/iPhone/iPad again or try to restart the
iPod/iPhone/iPad.
≥ When this unit is in standby mode, charging will not start
when using the “IPOD_PORT” connection.
Turn this unit on and make sure the charging has started
before switching this unit to standby mode.
The remote control doesn't work properly.
≥ The remote control and this unit are using a different
code. (l right, “REMOTE ”)
≥ Is the battery depleted or is the battery inserted
incorrectly? (l 4)
The following messages or service numbers
may appear on the unit's display.
“--:--”
≥ You plugged the AC power supply cord in for the first time or
there was a power failure recently. Set the time (l 9).
“ADJUST CLOCK”
≥ Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
≥ Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
≥ The unit has been left unused for about 30 minutes and will
shut down within a minute. Press any button to cancel it.
“CHECKING CONNECTION”
≥ The unit is checking the connected iPod/iPhone/iPad.
≥ If this display keeps appearing, make sure that the battery of
the iPod/iPhone/iPad is not depleted and that the iPod/
iPhone/iPad is turned on and connected correctly (l 6).
“DIMMER”
≥ Appears 10 seconds after the volume is turned to “0”.
“DOCK OPEN”
≥ Is the dock open? Close the dock completely to open the
sliding door.
“ERROR”
≥ Incorrect operation is performed. Read the instructions and
try again.
“F ” (“ ” stands for a number.)
≥ There is a problem with this unit.
Note down the displayed number, disconnect the AC power
supply cord and consult your dealer.
“ILLEGAL OPEN”
≥ Sliding door is not in correct position. Turn the unit off and on
again. If this display appears again, consult the dealer.
“IPOD_DOCK OVER CURRENT ERROR”
“IPOD_PORT OVER CURRENT ERROR”
≥ The iPod/iPhone/iPad is drawing too much power.
Disconnect the iPod/iPhone/iPad and turn the unit off and on
again.
“NODEVICE”
≥ The iPod/iPhone/iPad device is not inserted correctly. Read
the instructions and try again (l 6).
≥ The battery of the iPod/iPhone/iPad is depleted. Charge the
iPod/iPhone/iPad and turn it on before connecting.
“NO DISC”
≥ Insert a disc to be played (l 6).
“NO PLAY”
≥ A CD that is not in CD-DA format is inserted. It cannot be
played.
“NOT SUPPORTED”
≥ You have connected an iPod/iPhone/iPad that cannot be
played (l 13).
≥ If the iPod/iPhone/iPad is compatible, turn it on and connect
it correctly.
“READING”
≥ The unit is checking the CD information. After this display
has disappeared, start operating.
“REMOTE ” (“ ” stands for a number.)
≥ The remote control and this unit are using different codes.
Change the code on the remote control.
– When “REMOTE 1” is displayed, press and hold [OK] and
[RADIO] for more than 4 seconds.
– When “REMOTE 2” is displayed, press and hold [OK] and
[CD] for more than 4 seconds.
iPod/iPhone/iPad operations
Remote control
Messages
SC-HC28~RQT9729.book Page 11 Friday, December 28, 2012 4:05 PM