Filter
Top Products
FEATURES AND INCLUDED ACCESSORIES
Clamping Level................................................................260V
Capacitance.......................................................30pf (approx.)
Suppression Modes............................Metallic & Longitudinal
Wires Protected.....................................2 wire/ 1 pr. (pins 4,5)
Connections................................RJ-11/45 Shared with LAN
GENERAL
Software.Included..(Windows95/98/ME/NT/2000/XP)
Hardware........................RS232 (open command set)
Programmable IR.........(learning) sends IR signals to
equipment after power failure
COMMUNICATION
TELEPHONE CIRCUIT
LAN CIRCUIT
CAPACITY
(VA)...............................................................................................1500VA
(Watts)...........................................................................................1000W
INPUT
Voltage Range...................................................................88Vac - 147Vac
Frequency Range.......................................................................47 - 63 Hz
OUTPUT
On Battery Output Voltage....................Pure Sine Wave at 120VAC +/- 5%
On Battery Output Frequency.................................................60 Hz +/- 1%
Transfer Time......................................................................................4ms
PROTECTION & FILTRATION
On Utility.....................................................Over/Under voltage protection
On Battery...........................................................Internal Current Limiting
Patented Power Management Circuit....................................................Yes
Overvoltage Shutoff....................................................................144V ±8V
Undervoltage Shutoff...................................................................90V ±6V
Thermal Fusing....................................................................................Yes
Initial Clamping Level.............................................200V Peak, 141V RMS
UL 1449 Suppression Rating.............................................................330V
Protection Modes.................................................................L-N, L-G, N-G
Response Time..................................................................................< 1 n
Single Pulse Energy Dissipation..............................................1650 Joules
Peak Impulse Current.................................................................52,000 A
EMI/RFI Noise Filtration........................................50dB (100kHz – 1 MHz)
AC CIRCUIT PROTECTION AND FILTRATION
Lightning Protection....................................................Yes
Product Warranty............................................3 Years
Design and specifications subject to change without
notice due to product improvement.
Compatibility......................................10/100 baseT Ethernet
Clamping Level.................................................................7V
Suppression Modes..............Differential & Common Ground
Wires Protected.........................................Pins 1, 2, 3 and 6
Connections..............................RJ/11--45 Shared with Telco
BATTERY
Sealed.............................................................................Yes
Maintenance-free..........................................................Yes
Lead Acid..............................................................Yes
User Replaceable..........................................................Yes
Typical Recharge Time.......................................8 hrs.
PHYSICAL
Rack Mountable...............Yes (rack mount kit included)
Maximum Dimensions
....17”W x 15.75" D x 4” H w/feet
Weight (lbs.)...........................................................56
Outlets.......................6 Total (2 assigned critical load)
TECHNICAL SPECIFICATIONS
© 2005 Panamax. The Panamax logo is a registered US trademark of Panamax.
ACRegenerator is a trademark of Panamax.
1690 Corporate Circle, Petaluma, CA 94954
800-472-5555 • 707-283-5900
Model: M1500-UPS
MAX® 1500-UPS
• Learning IR Function • Critical Load Status Outlets • RS-232 Interface • Noise Filtration/Power Protection
L544 REV. C 10/05
Test Switch
This UPS performs a self-test automati-
cally when powered on. The test switch
allows you to test the system at any
time. In battery mode, you can press
this button to silence an audible alarm.
Power On Indicator
This LED is illuminated when the
utility condition is normal and the
UPS outlets are providing clean,
protected power.
Line Fault Indicator
This LED will illuminate to warn the user that a
wiring problem such as a bad/missing ground or
reversed wiring exists within the AC receptacle.
If illuminated, disconnect all equipment and contact
an electrician to insure outlet is properly wired.
Unsafe Voltage Indicator
This LED will illuminate to inform the user
that an unsafe line voltage is present and
that the UPS has switched to battery power.
This could be either an over-voltage or
under-voltage.
Power Switch
Press the power button to
turn the UPS ON or OFF.
AVR Indicator
This indicates that the UPS is operating in automatic voltage regulation mode.
When the led is illuminated continuously, it indicates an input over-voltage
and the UPS unit reduces the voltage to the normal operating range. When
the led is flashing, it indicates that the input line voltage is low and that the
UPS is increasing voltage to the normal range.
Battery Level Indicator
This is a visual indication of the battery
charge. If battery capacity is under
20%, no indicator LED will illuminate
and UPS starts beeping (if the audible
alarm is enabled).
Battery Mode Indicator
This illuminates during utility failure
or an unsafe voltage condition, indi-
cating that the battery is supplying
power to the connected equipment.
Removable Access Panel
Easy to remove for battery
access and replacement
Acessories Included:
1 - IEC 320, 120V/15A Power Cord
1 - RJ-11 Telephone Cable
1 - DB 9 Serial Cable
1 - Home Cinema Power Control
Software
2 - Rack Mounting Ears
Circuit Breakers for Overload Protection
Resettable circuit breakers provide optimal overload protection.
Non-Critical-Load Outlets
Four battery powered, surge protected
and AVR outlets for connected equipment
insures temporary uninterrupted opera-
tion of connected equipment during a
power failure.
Critical Load Outlets
Two battery powered, surge protected and AVR outlets for
critical-load equipment insures temporary uninterrupted
operation of connected equipment during a power failure.
IR Control Section
Learning Control Switches – Push to program or test the IR function
IR Detector Window – Receives the IR signal to be learned
Indicator LED’
s – Indicates learning status
Output Delay Switches
– Set the desired time delay between a power
failure and when the IR signals are sent to the connected equipment
IR Output Jacks – Standard 1/8” (3.5mm) mono jack for connection
to an IR flasher (IR flashers not included)
RS232 Serial Communication Port
The serial port allows connection and communication between the UPS and a HTPC (home theater personal
computer) or home automation system. If used temporarily during setup (with the included software), it
allows the installer to program a number of variables including the Critical Load Battery Threshold.
RJ11/RJ45 Jacks
Ports protect standard
telephone line, modem,
or network cable.
AC Power
Cord Input
Receptacle
www.panamax.com
Single Pack Dimensions............19.25”W x 10.25”D x 18.5”H
Single Pack Weight.........................................................65 lbs.
Single Unit UPC.............................................0 50616-00763 4
Master Pack Dimensions..........19.75”W x 10.75” D x 19.25” H
Master Pack Qty................................................................1 Unit
Master Pack Weight.........................................................65 lbs.
Master Pack UPC...............................Same as Single Unit UPC
SHIPPING DIMENSIONS, WEIGHTS AND UPC CODES
Load Level Indicator
This is a visual indication of the UPS load.
The 1st arrow will illuminate when the load
is above 25%, the 2nd above 50% and the
3rd above 75%. The 4th arrow will flash
when the load is between 85% and 100%.