Filter
Top Products
Step 2: Setting Up
En-10
Setting speaker distance
1. After pressing RECEIVER, press SETUP on the
remote controller.
2. Select "2. Speaker" with the cursor, and press
ENTER.
3. Select "Distance" with the cursor, and press ENTER.
Distances can be set in feet or meters.
Unit
Front Left
Center
Front Right
feet
12.0ft
12.0ft
12.0ft
2-3. Distance
Use the cursors
d
/
c
to configure the distance from each
speaker to the listening position. When setting is complete,
press SETUP to close the menu screen.
● Some setting items may not be selectable depending on
the settings of "Configuration".
Adjusting volume level of speakers
1. After pressing RECEIVER, press SETUP on the
remote controller.
2. Select "2. Speaker" with the cursor, and press
ENTER.
3. Select "Level Calibration" with the cursor, and press
ENTER.
Sets the volume lebel of the front left speaker.
Front Left
Center
Front Right
0dB
0dB
0dB
2-4. Level Calibration
Move the cursor with
d
/
c
buttons and change the
volume level of each speaker. A test tone will be output
each time you change the level. Select the desired level.
When setting is complete, press SETUP to close the menu
screen.
● This setting cannot be changed when muting is enabled.
● Some setting items may not be selectable depending on
the settings of "Configuration".
3 HDMI Setup
The unit supports the linked system function such as power
on/off link when connected via HDMI cable with a CEC
(Consumer Electronics Control) compliant TV or player. You
need to change the default setting to use the linked system
function, HDMI Standby Through function and ARC (Audio
Return Channel) function.
HDMI CEC (RIHD)
The following linked operations are possible with connected
equipment when the CEC function is enabled.
●
Turning the TV to standby mode will turn the unit to
standby mode.
●
On the TV side, it is possible to set whether to output
audio from the speakers connected to the unit or from the
TV's speakers.
●
Starting playback of a CEC compliant player/recorder will
automatically switch the unit's input to the HDMI input of
the player/recorder. If the unit is in standby mode, it will
automatically be turned on.
It is also possible to control the connected CEC compliant
equipment with the remote controller of the unit. For details,
see the Advanced Manual.
¼ RIHD is a name for the linked system function of Onkyo's CEC compliant
products.
1. After pressing RECEIVER, press SETUP on the
remote controller.
2. Select "5. Hardware" with the cursor and press
ENTER.
3. Select "HDMI" with the cursor and press ENTER.
4. Select "HDMI CEC (RIHD)" with the cursor and
select "On".
● When setting is complete, press SETUP to close the
menu screen.
HDMI Standby Through
The function allows transmission from players to the TV
even if the unit is in standby. Setting the HDMI CEC (RIHD)
setting mentioned above to "On" enables this setting
automatically.
● Power consumption in standby mode increases when
the HDMI Standby Through function is enabled.
ARC (Audio Return Channel)
Simple connection to the ARC compatible TV using a single
HDMI cable allows to listen to the TV audio signals from
the speakers connected to the unit. Setting the HDMI CEC
(RIHD) setting mentioned above to "On" enables the "Audio
Return Channel" setting automatically.
Audio output of connected players
To enjoy digital surround sound including Dolby
Digital and DTS, audio output should be set to
"Bitstream output" on the connected Blu-ray Disc
Player or other device.
Depending on the settings on the Blu-ray Disc Player,
there may be cases when Dolby TrueHD and DTS-
HD Master Audio is not output according to the format
of the source.
In this case, in the Blu-ray Disc Player settings
try setting "BD video supplementary sound" (or
secondary sound) to "Off".
Change the listening mode after changing the setting
to confirm.