Filter
Top Products
Advanced Operations
En-54
Main menu Speaker Setup
Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the
connected speakers after using Audyssey 2EQ Room
Correction and Speaker Setup function.
Speaker Settings
If you bi-amp the front speakers, you must change the
“Speakers Type (Front)” setting. For details on speaker
wire connection, see “Bi-amping the Front Speakers”
(➔ page 14).
Note
• When bi-amping is used, the AV receiver is able to drive up to 5.1
speakers in the main room.
• Before you change these settings, turn down the volume.
■ Speaker Impedance
(European, Australian and Asian models)
`4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
`6ohms
:
Select if the impedances of all speakers are between 6
and 16 ohms.
Note
• (North American and Taiwanese models) Speakers with an
impedance of less than 6 ohms are not supported.
■ Speakers Type (Front)
`Normal
:
Select this if you’ve connected your front speakers
normally.
`Bi-Amp:
Select this if you’ve bi-amped your front speakers.
■ Powered Zone 2
`No
`Yes:
Zone 2 speakers can be used. (Powered Zone 2
enabled).
Note
• If the “Speakers Type (Front)” setting is set to “Bi-Amp”,
Powered Zone 2 cannot be used.
• When the “Powered Zone 2” setting is set to “Yes” and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “Full Band” for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey 2EQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to “80Hz(THX)” crossover.
■ Subwoofer
`Yes
`No
■ Front
`Full Band
`40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz, 200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
■ Center
*1
, Surround
*1
`Full Band
`40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz, 200Hz
`None
■ Front High
*1*2*3*5
`Full Band
`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz
`None
■ Surround Back
*1*2*3*4
`Full Band
`40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz, 200Hz
`None
Note
*1
“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
If the “Surround” setting is set to “None”, this setting cannot
be selected.
*3
If the “Speakers Type (Front)” setting is set to “Bi-Amp”, or
the “Powered Zone 2” setting is set to “Yes” together with
Zone 2 turned on, this setting cannot be selected.
*4
If anything else than “None” is selected in “Front High”, this
setting is automatically set to “None”.
*5
If anything else than “None” is selected in “Surround Back”,
this setting is automatically set to “None”.
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey 2EQ
®
Room Correction and Speaker Setup
(➔ page 34).
If you change these settings, you must run
Audyssey 2EQ Room Correction and Speaker Setup
again (➔ page 34).
1 2 3 4 5
“Setup”
This setting is set automatically by Audyssey 2EQ Room
Correction and Speaker Setup (➔ page 34).