Filter
Top Products
54
First Time Setup—Continued
HDMI Input Setup
If you connect a video component to HDMI IN, you
must assign that input to an input selector. For example,
if you connect your DVD/BD player to HDMI IN 1, you
must assign HDMI IN 1 to the DVD/BD input selector.
If you’ve connected your TV to the AV receiver with an
HDMI cable, you can set the AV receiver so that
composite video, S-Video, and component video sources
are upconverted* and output by the HDMI output. You
can set this for each input selector by selecting the
“-----” option.
Notes:
• For composite video, S-Video, and component video
upconversion for the HDMI output, the “Monitor Out”
setting must be set to other than “Analog” (see
page 52), and the “HDMI Input” setting must be set to
“- - - - -”. See page 32 for more information on video
signal flow and upconversion.
• If no video component is connected to HDMI output
(even if the HDMI input is assigned), the AV receiver
selects the video source based on the setting of
Component Video Input.
• When an HDMI IN is assigned to an input selector, the
AV receiver will select audio from HDMI IN as a pri-
ority. See “Digital Audio Input Setup” on page 56.
• The TUNER input selector cannot be assigned and is
fixed at the “- - - - -” option.
• If you connect an input component (such as UP-A1
Dock that seated iPod) to the UNIVERSAL PORT
jack, you cannot assign any input to PORT selector.
• Do not assign the component connected with the
HDMI input to the TV/TAPE selector when you set
“TV Control” setting to “On” (see page 114).
Otherwise, appropriate CEC (Consumer Electronics
Control) operation is not guaranteed.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
Video Input Setup
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [ ]/[ ] but-
tons to select “1. Input/Output
Assign”, and then press
[ENTER].
The “Input/Output Assign” menu
appears.
3
Use the Up and Down [ ]/[ ] but-
tons to select “2. HDMI Input”,
and then press [ENTER].
The “HDMI Input” menu appears.
IN
OUT
Composite video, S-Video,
component video
Composite video, S-Video,
component video
HDMI
HDMI
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
1–2. HDMI Input
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX 1
HDMI1
HDMI2
HDMI3
HDMI4
FRONT
4
Use the Up and Down [ ]/[ ] but-
tons to select an input selector,
and use the Left and Right [ ]/
[ ] buttons to select:
HDMI1, HDMI2, HDMI3, HDMI4,
HDMI5, HDMI6,
HDMI7 (TX-NR5007):
Select the HDMI IN to which
the video component has
been connected.
-----: Output composite video,
S-Video, and component
video sources from the HDMI
outputs. The video output sig-
nal from the HDMI outputs is
the one configured in “Com-
ponent Video Input Setup”
(see page 55).
• Each HDMI IN cannot be assigned to
more than one input selector. When
HDMI IN have already been
assigned, you must set first any
unused input selectors to “- - - - -” or
you will be unable to assign HDMI
IN to input selector.
• “AUX 1” is used only for digital
input from the front panel terminals.
5
Press the [SETUP] button.
The setup menu closes.