Filter
Top Products
40
Audio Adjust
3. Audio Adjust Setup menu
Set the various parameters for the sound signals.
Surround L/R: This outputs the sound to the surround left and
right speakers as normal and outputs nothing to the surround
back speaker.
Surround Back: This outputs the sound to the surround back
speakers and outputs nothing to the surround left and right
speakers.
Sur L/R+Back: This outputs the sound to both the surround left
and right speakers and the surround back speaker.
Note:
If the Surr Back Out setting in the Speaker Config sub menu is set to
“1ch,” the Surround Speakers sub menu is disabled.
3-3. Sound Effect
Turn on and off the various sound effects.
Parameter Setting
Initial value
a RE-EQ On, Off Off
b Upsampling On, Off Off
c Subwoofer On, Off On
(Ana/PCM)
d Late Night Off, Low, High Off
a) Re-EQ
Re-EQ (re-equalization) takes the edginess or “brightness” out of
your home cinema sound to compensate for the fact that sound
mixed for theaters may sound too bright when played back through
speakers in the home environment.
This can be set to either “On” or “Off.”
This parameter is enabled for listening modes other than the THX,
T-D, Direct, PL II Music, or Neo:6 Music listening mode.
b) Upsampling
Upsampling processes the input digital signal, or the digital signal
converted from an analog input source, and converts its digital
sampling frequency to twice its current frequency for an even further
detailed sound reproduction. This can be set to either “On” or “Off.”
When “On” is selected, the UPSAMPLING indicator lights.
c) Subwoofer
When “Yes” is selected for the Subwoofer setting in the Speaker
Config sub-menu, set this to “Off” if you do not want to have sound
output from the subwoofer. This setting is only effective when the
input source is Analog/PCM. If “No” is selected for the Subwoofer
setting in the Speaker Config sub-menu, then this setting will not
appear.
d) Late Night
Cinema sound has a vast dynamic range; therefore, to hear the
quieter sounds such as human conversations, they must be played
back at larger volumes. When this parameter is set to “High” or
“Low,” the dynamic range of the sound is narrowed down to allow
you to easily hear minute sounds at low volumes. This function is
especially useful if you wish to play a movie at low volumes during
the nighttime.
This can be set to either “Off” or “Low,” or “High.”
When this parameter is set to High or Low, the dynamic range of the
sound is narrowed down to allow you to easily hear minute sounds at
low volume.
Off: Turns off the Late Night function.
Low: Lowers the dynamic range.
High: Narrows down the dynamic range.
Notes:
• The Late Night function is effective only on Dolby Digital
encoded software.
• The depth of the Late Night effect is determined by Dolby
Digital software. Some sounds may produce no or little effect.
Advanced Menu
3.Audio Adjust
3-1.Tone Control
a.Bass : 0
b.Treble : 0
Quit:|SETUP|
3-1. Tone Control
Separately adjust the bass and treble settings as desired in 2-decibel
units.
Note:
If DIRECT or THX is selected as the listening mode, these settings
cannot be made. To make these settings, first select another listening
mode.
3-2. Surround Speakers
This setting allows you to decide which speakers to output to when
surround back speakers are connected and you are playing back a
5.1-channel source.
Parameter Setting
Initial value
a Surround Speakers Surround L/R, Surround Back, Surround L/R
Surr L/R + Back
Parameter Setting
Initial value
a Bass –12 to +12 0
b Treble –12 to +12 0
Basic Menu
3.Audio Adjust
1.Tone Control
2.Surround Speakers
3.Sound Effect
→
default
Advanced Menu
3.Audio Adjust
1.Tone Control
2.Surround Speakers
3.Sound Effect
4.Delay
5.LFE Level
6.Mono Setup
7.Theater-Dimensional
8.Surround Setup
Advanced Menu
3.Audio Adjust
9.THX Setup
10.Mono Movie Setup
11.Enhanced 7 Setup
12.Orchestra Setup
13.Unplugged Setup
14.Studio Mix Setup
15.TV Logic Setup
→
default