Filter
Top Products
42
En
Menu HDMI Setup
■ HDMI Ctrl (RIHD)
`Off
`On
Turn this setting on to allow -compatible
components connected via HDMI to be controlled by the
AV receiver (➔ page 57).
Note
• When set to “On” and close the menu, the name of connected
-compatible components and “RIHD On” are
displayed on the AV receiver.
“Search…” → “(name)” → “RIHD On”
When the AV receiver cannot receive the name of the
component, it is displayed as “Player*” or “Recorder*”, etc
(“*” means the number of two or more component).
• When an -compatible component is connected to the
AV receiver via the HDMI cable, the name of the connected
component is displayed on the AV receiver display. For
example, while you are watching TV broadcasting, if you
operate a Blu-ray Disc/DVD player (being powered on) by the
remote control of the AV receiver, the name of the Blu-ray
Disc/DVD player is displayed on the AV receiver.
•Set to
“Off” when a connected piece of equipment is not
compatible or it is unclear whether the equipment is compatible
or not.
• If movement is unnatural when set to
“On”, change the setting
to
“Off”.
• Refer to the connected component’s instruction manual for
details.
• When “HDMI Ctrl (RIHD)” setting is set to “On”, the power
consumption on standby mode slightly increases. (Depending on
the TV status, the AV receiver will enter standby mode as usual.)
■ HDMI Through
`Off
`Auto:
Detects the signal and automatically selects the input
source.
`BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,
TV/CD:
Selects the input source for which the HDMI
Through function is enabled.
`Last:
The HDMI Through function is activated on the
input source selected at the time of setting the AV
receiver to Standby mode.
When enabling the HDMI Through function, regardless of
whether the AV receiver is On or in Standby, both audio
and video stream from an HDMI input will be output to
the TV or other components via HDMI connection. The
HDMI THRU and HDMI indicators light when enabled.
This setting is set to “Auto” automatically when the above
“HDMI Ctrl (RIHD)” is set to “On”.
Note
• Only the input source assigned to the HDMI IN via
“HDMI Input” is enabled (➔ page 35).
• The power consumption during standby mode will increase
during the HDMI through function; however in the following
cases, the power consumption can be saved:
– The TV is in standby mode.
– You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
• Depending on the connected component, the correct input source
may not be selected with the setting set to “Auto”.
• This setting is set to “Off” automatically when the “HDMI Ctrl
(RIHD)” setting is set to “Off”.
■ Audio TV Out
`Off
`On
This preference determines whether the incoming audio
signal is output from the HDMI output. You may want to
turn this preference on if your TV is connected to the
HDMI output and you want to listen to the audio from a
connected component through your TV’s speakers.
Normally, this should be set to “Off”.
Note
• Listening mode cannot be changed when this setting is set to
“On” and the input source is not HDMI.
•If
“On” is selected and the signal can be output from the TV, the
AV receiver will output no sound through its speakers. In this
case, “TV Speaker” appears on the display by pressing
DISPLAY.
•When
“HDMI Ctrl (RIHD)” is set to “On”, this setting is fixed
to
“Auto”.
• With some TVs and input signals, no sound may be output even
when this setting is set to
“On”.
•When the “Audio TV Out” setting is set to
“On”, or “HDMI
Ctrl (RIHD)” is set to
“On” and you’re listening through your
TV’s speakers (➔ page 14), if you turn up the AV receiver’s
volume control, the sound will be output from the AV receiver’s
front left and right speakers. To stop the AV receiver’s speakers
producing sound, change the settings, change your TV’s
settings, or turn down the AV receiver’s volume.
■ Audio Return Ch (ARC)
`Off
`Auto
:
The audio signal from your TV tuner can be sent to
the HDMI OUT of the AV receiver.
The audio return channel (ARC) function allows an ARC
capable TV to send the audio stream to the HDMI OUT of
the AV receiver. To use this function, you must select the
TV/CD input selector and your TV must support ARC
function.
Note
• If you set “Audio Return Ch” to “Auto”, the “Audio Selector”
settings of the TV/CD input selector will be automatically
switched to “ARC” (➔ page 40).
•The “Audio Return Ch” setting can be set only when the above
“HDMI Ctrl (RIHD)” setting is set to “On”.
• This setting is set to “Auto” automatically when the above
“HDMI Ctrl (RIHD)” is set to “On” first time.
HDMI Setup