Filter
Top Products
17
ENGLISH
FRANÇAISDEUTSCHNEDERLANDSESPAÑOL
ITALIANO
PORTUGUÊS
SVENSKA
Now rotate the VOLUME/SETUP knob until REAR LAR (current setting for
the SURROUND speakers) appears in the display window. Press the SET
UP button again to change the size. Each press of the SET UP button will
change the setting for that speaker:
REAR (Surround Speakers) can be set to LAR, SMA or OFF.
Now rotate the VOLUME/SETUP knob until SUB ON (current setting for
the Subwoofer) appears in the display window. Press the SET UP button
again to change the setting. Each press of the SET UP button will change
the setting for that speaker:
SUB (subwoofer) can be set to ON, OFF.
Now rotate the VOLUME/SETUP knob until EXIT appears in the display
window. Press the SET UP button again to exit SPEAKER SETTING MENU.
Press the SET UP button again to exit the SET UP MENU. Your speaker
settings are now complete. If in the future you add or change speakers,
this setup procedure should be repeated.
TIPS ON WHICH SPEAKER SETTINGS TO USE
The four modes available to the T742’s setup are: LARGE or SMALL and
ON or OFF.
The LARGE mode is used when the speaker is full range and capable of
reproducing the entire audible frequency spectrum 20Hz to 20kHz. The
SMALL mode is used when the speaker is not capable of reproducing the
deepest bass portion of the audio frequency 20Hz to 100Hz.
The ON mode is used when the speaker is active and receives the audio
information intended. The OFF mode is used when the speaker is
inactive. Audio signals intended for speakers set to the OFF position are
redirected to the main speakers.
Using a separate centre channel speaker will allow the dialogue to cut
through even the biggest sound effects and musical scores. Having the
sound spread across three front speakers also stabilizes the stereo image,
making the usable listening area much bigger. For best results, you
should consider using a centre speaker. Ideally it should be the same type
as the left and right speakers.
Installing surround speakers will greatly enhance the surround experience
as these add considerably to the overall “ambience”.
Dolby Pro Logic encoded material is deliberately limited in dynamic range
and frequency bandwidth for the surround channel and thus only
requires speakers of far lesser specification compared to the front
channels. Dolby Digital however is a full range system, with two
independent surround channels and with dynamics equal to that of the
front channels. For this reason it is advisable to choose loudspeakers
which are similar in power handling and performance capability to those
of the front channels. For best results, the Surround loudspeakers should
not beam the sound directly at the listener. One way of achieving this is
to use ‘dipole’ Surround speakers which aim the sound down the walls
rather than directly into the room.
Many film soundtracks rely heavily on very low frequency sound effects
which are difficult for normal or smaller hi-fi speakers to reproduce. To
faithfully reproduce these low frequencies you can use a specially
designed low frequency loudspeaker with its own built-in amplifier
(“active subwoofer”). Because it is difficult to hear which direction very
low frequencies are coming from, you only normally need one sub-
woofer and this can be placed virtually anywhere in the room. The
Subwoofer output of the T742 is designed specifically to drive a
subwoofer system.
Dolby Digital uses a dedicated Low Frequency Effects (LFE) channel. If a
subwoofer has been selected, the LFE channel will be fed to the sub-
woofer output. If no subwoofer is selected the LFE channel is redirected
to the front left and right speakers.
CHANNEL DELAYS
For the best surround sound performance it is important that sound from
all speakers reach the listener’s ears at the same time. Because the
surround/ rear speakers are usually closer to the listener than the front
speakers, there is tendency for the ear to localize sounds to the rear,
because the ear takes most notice of the sounds that arrive at the head
first. Similarly, the centre speaker is often closer to the listener than the
front left and right speakers. To compensate for this, the T742 can
slightly delay the audio sent to the centre and rear (closer) speakers. In
this way, when playing Dolby Digital or Dolby Pro logic soundtracks, the
sound from all speakers arrives uniformly at the listening position as
intended by the film’s producer.
Each millisecond corresponds approximately with 1 foot or 30.5
centimeters.
NOTE
The channel delay option is not available in DTS surround mode.
TO ADJUST DELAY SETTINGS
When Front Panel Display shows DELAY, pressing the SET UP button on
front panel again (second press) will enter the DELAY SETTING menu.
Rotate VOLUME/SETUP knob to cycle between CENT > REAR > EXIT.
First stop at CEN 0mS (current delay setting for Centre Speaker). Press
the SET UP button again to change the delay setting. Rotate the
VOLUME/SETUP knob to change centre delay adjustment in 1mS
increments from 0mS to 5mS. Press SET UP button again to exit Centre
delay adjustment.
Now rotate the VOLUME/SETUP knob until REAR 0mS (current delay setting
for Surround Speakers) appears in the display window. Press the SET UP
button again to change the delay setting. Rotate the VOLUME/SETUP knob
to change centre delay adjustment in 1mS increments from 0mS to 15mS
in Dolby Digital mode, or 15mS to 30mS in Dolby ProLogic mode. Press SET
UP button again to exit Rear delay adjustment.
Now rotate the VOLUME/SETUP knob until EXIT appears in the display
window. Press the SET UP button again to exit DELAY SETTING MENU.
Press the SET UP button again to exit SET UP MENU. Your speaker
settings are now complete. If in the future you add, change, or move
speakers, this setup procedure should be repeated.