THX subwoofers page 9
FIGURE 3 - WIRING ONE SUBWOOFER TO AN AMP OR PROCESSOR
WITH A SUBWOOFER OUTPUT JACK (NON-THX)
SURROUND
PROCESSOR
SUBWOOFER (or MONO) OUT
10391 Jefferson Blvd
Culver City, CA 90232
310/204-2854
MILLER & KREISEL
SOUND CORP.
RIGHT
INPUT
REFERENCE
80 Hz
24 dB/
OCTAVE
Made in U.S.A.
T
6 AMP
120 VAC
50/60 Hz
LEFT/MONO
SLOW-BLOW
ATTENTION:
DEBRANCHER AVANT DE
REMPLACER LE FUSIBLE.
UTILIZER UN FUSI BLE
DE RECHANGE
DE MEME TYPE.
CAUTION:
DISCONNECT SUPPLY CORD
BEFORE CHANGING FUSE.
REPLACE FUSE ONLY
WITH SAME TYPE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
AVIS:
RISQUE DE
CHOC ELECTRIQUE.
NE PAS OUVRIR.
Manufactured under license
from Lucasfilm Ltd.
Lucasfilm and THX are
registered trademarks
of Lucasfilm Ltd.
EXTENDED
THX
+
PHASE
THX MODE
NO LOW
PASS FILTER
LOW PASS FILTER
+3 dB
+6 dB
BASS LEVEL
BASS EQ
50
75
60
125
100
V
A
R
I
A
B
L
E
VARIABLE
THX
CENTER SWITCH
POSITION FOR
VARIABLE
LOW PASS
MX-350
THX
POWERED SUBWOOFER
use a Y-connector
to connect to
two subwoofers
SURROUND
PROCESSOR
SUBWOOFER (or MONO) OUT
10391 Jefferson Blvd
Culver City, CA 90232
310/204-2854
MILLER & KREISEL
SOUND CORP.
RIGHT
INPUT
REFERENCE
80 Hz
24 dB/
OCTAVE
Made in U.S.A.
T
6 AMP
120 VAC
50/60 Hz
LEFT/MONO
SLOW-BLOW
ATTENTION:
DEBRANCHER AVANT DE
REMPLACER LE FUSIBLE.
UTILIZER UN FUSIBLE
DE RECHANGE
DE MEME TYPE.
CAUTION:
DISCONNECT SUPPLY CORD
BEFORE CHANGING FUSE.
REPLACE FUSE ONLY
WITH SAME TYPE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
AVIS:
RISQUE DE
CHOC ELECTRIQUE.
NE PAS OUVRIR.
Manufactured under license
from Lucasfilm Ltd.
Lucasfilm and THX are
registered trademarks
of Lucasfilm Ltd.
EXTENDED
THX
+
PHASE
THX MODE
NO LOW
PASS FILTER
LOW PASS FILTER
+3 dB
+6 dB
BASS LEVEL
BASS EQ
50
75
60
125
100
V
A
R
I
A
B
L
E
VARIABLE
THX
CENTER SWITCH
POSITION FOR
VARIABLE
LOW PASS
MX-350
THX
POWERED SUBWOOFER
10391 Jefferson Blvd
Culver City, CA 90232
310/204-2854
MILLER & KREISEL
SOUND CORP.
RIGHT
INPUT
REFERENCE
80 Hz
24 dB/
OCTAVE
Made in U.S.A.
T
6 AMP
120 VAC
50/60 Hz
LEFT/MONO
SLOW-BLOW
ATTENTION:
DEBRANCHER AVANT DE
REMPLACER LE FUSIBLE.
UTILIZER UN FUSIBLE
DE RECHANGE
DE MEME TYPE.
CAUTION:
DISCONNECT SUPPLY CORD
BEFORE CHANGING FUSE.
REPLACE FUSE ONLY
WITH SAME TYPE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
AVIS:
RISQUE DE
CHOC ELECTRIQUE.
NE PAS OUVRIR.
Manufactured under license
from Lucasfilm Ltd.
Lucasfilm and THX are
registered trademarks
of Lucasfilm Ltd.
EXTENDED
THX
+
PHASE
THX MODE
NO LOW
PASS FILTER
LOW PASS FILTER
+3 dB
+6 dB
BASS LEVEL
BASS EQ
50
75
60
125
100
V
A
R
I
A
B
L
E
VARIABLE
THX
CENTER SWITCH
POSITION FOR
VARIABLE
LOW PASS
MX-350
THX
POWERED SUBWOOFER
FIGURE 4 -WIRING TWO SUBWOOFERS TO AN AMP OR PROCESSOR
WITH A SUBWOOFER OUTPUT JACK (NON-THX)
If your surround processor has only one PREAMP OUTPUT (and no SUBWOOFER OUT), and you
do not have an M&K High-Pass Filter or crossover, you must use a Y-connector to feed the amplifier
and subwoofer. See Figure 5 on page 10. If you have a surround sound processor with a
SUBWOOFER OUTPUT jack, use it to feed the subwoofer. See Figure 3 above.
If you are using two subwoofers, it is not necessary to use both inputs on each subwoofer. Connect
the interconnect cable to the LEFT/MONO "INPUT jack only. Run the Left channel interconnect cable
to the Left subwoofer and the Right interconnect cable to the Right subwoofer. See Figure 4.
Some surround processors/receivers/amps have very low output levels from their SUBWOOFER
OUTPUT jacks. If you do not get enough bass using the SUBWOOFER OUTPUT jacks on a non-THX
processor, use that processor's PREAMP OUTPUT jacks instead. To connect the subwoofer, run
shielded RCA - RCA interconnect cables from the outputs on your component to the "INPUT" jacks
found on the subwoofer's backplate. See Figure 5 on page 10.
If your processor has a single subwoofer output, do not use a Y-connector to connect it to both the
Left and Right input terminals of the subwoofer. The subwoofer combines both channels to mono in
its amplifier input stage.