Filter
Top Products
owners manual
2
IMPORTANT SAFETY
INSTRUCTIONS -
READ CAREFULLY !
Read Instructions: All safety and operating instructions should be read before the product is
operated.
Retain instructions: Safety and operating instructions should be retained for future reference.
Heed Warnings: All warnings on the product & operation instructions should be adhered to.
Follow Instructions: All operating and use instructions should be followed.
Cleaning: Unplug the product from the wall before cleaning. Do not use aerosol or liquid
cleaners, just a damp cloth.
Damage Requiring Service: The product should be serviced by qualified personnel when:
A. The appliance does not appear to operate normally or exhibits a marked
change in performance; or
B. Product has been dropped, or damaged.
C. If the product does not operate normally by following the operating instructions.
INTRODUCTION
Congratulations on your purchase of Mirage Speaker Systems products! Proprietary technology
and high quality manufacturing will allow you to enjoy the most natural and accurate music
reproduction for many years. The advice offered in this manual is aimed at helping you
maximize and maintain peak performance, and therefore, your listening satisfaction. Please
take the time to read all of the instructions contained in this manual to make certain your
system is properly installed and functioning correctly.
BREAK-IN PERIOD
We strongly advise that you resist the temptation to play your Mirage Speaker Systems speakers
to their full capabilities until they have been properly broken in. This process should last
approximately 50 to 100 hours of music playback. This can be easily be done by putting your
compact disc player on Repeat mode, while playing a CD with a wide dynamic range at average
room volume listening levels.
AMPLIFIER REQUIREMENTS
All Mirage speakers are designed to be extremely efficient. All models are designed to be 8 ohm
compatible allowing playback on almost any amplifier or receiver on the market. Most amplifiers
with a power rating of 20-100 watts per channel will effectively operate your Mirage speakers.
Warning: If an amplifier or receiver is over-driven, the resulting distortion is actually many
times greater than its rated power. Over-driven amplifier distortion is called “Clipping”,
easily identified by its fuzzy, distorted sound, and can damage any speaker. The volume
control of most amplifiers and receivers is a logarithmic type, which means that full power
may be reached with the volume control set at as little as the halfway point. Operating the
loudness, treble, or bass controls increases power output well beyond rated levels. The
warranty on your speakers is therefore void if the voice coils are burned or damaged as a
result of overpowering or clipping.
LIMITED WARRANTY POLICY
WARRANTY FOR UNITED STATES AND CANADA (see back cover)
Warranty Outside of The United States and Canada:
Product warranties may be legislated differently from one country to another. Ask your local
dealer for details of the LIMITED WARRANTY applicable in your country.
NOTE: Please retain the carton and packing material for your Mirage Speaker Systems
products to protect them in the event of a move or if they need to be shipped to a service
center. Product received damaged by a service center that has been shipped by the end user
in other than the original packaging will be repaired, refurbished and properly packaged for
return shipment at the end user's expense.
INSTALLATION INSTRUCTIONS
NOTE: If you are unable to install the speakers yourself , please contact an authorized
installation contractor, or your authorized Mirage Speaker Systems retailer.
Caution: Turn off all power in your audio/video system before proceeding with your
installation. Not doing so could result in potential damage to the system.
To install the speakers follow these easy steps:
1) Decide the placement for your speakers. Advanced planning in regards to the placement of your
speakers is critical. It is imperative that the wall or ceiling cavity be free from debris, moisture,
wall insulation, and any material that is easily combustible. The mounting location must also be
void of wall studs or bracing, in the location for the cut-out. Adequate depth for the speaker to
fit flush to the wall or ceiling surface is important. If you are unsure about the contents of the
wall in which you wish to mount the speakers, simply drill a small hole and using a metal
clothing hanger, insert the end of the hanger into the wall and twist it to feel for any debris or
wall studs.
2) Once you have determined the final mounting position, use the supplied template and mark the
cut-out on the wall or ceiling, depending on the model purchased. To mark the cut-out size,
simply trace an outline of the supplied template, found in the box, with a pencil.
3) Using the appropriate wall cutting tool, accurately cut the hole in the wall material, based on
the appropriate cut-out dimension.
4) Install speaker cable(s) from the receiver or amplifier to the inside of the wall or ceiling, and
leave enough slack in the wire so it can hang out from the hole. Using the appropriate wire is
essential, as your local municipality may have certain wiring codes that must be maintained.
NOTE: To connect the i-6Cst you will need to run both the left and right speaker cables to
one single hole as this speaker has stereo input connectors.
5) Connect the speaker wire from the positive (RED +) terminal on the receiver to the positive
(RED+) terminal on the speaker. Connect the negative (BLACK-) terminal on the receiver to the
negative (BLACK-) terminal on the speaker. To connect the wire to the speaker, completely push
the appropriate terminal in, and insert the wire through the hole that appears on the terminal.
Release the terminal and the internal springs will hold the wire in place. Repeat for the other
terminal.
NOTE: If you inadvertently reverse one of the connections (i.e, red to black), you will notice a
severe lack of bass from your system. This is called wiring the system “Out of Phase”. If this
occurs, check the wiring and re-connect as necessary.
NOTE: To connect the i-6Cst you must repeat the connection procedure for both left and right
channels on one i-6Cst speaker. This speaker has dual input terminals providing sound for
both the left and right channels of your amplifier or receiver.
In Ceiling Models: (i-6C, i-8C, i-6Cst)
6) Insert the entire speaker into the hole, and using a Philips screwdriver, tighten the screws
attached to the dog clamps until firm. DO NO
T OVERTIGHTEN
In Wall Models: (i-6W)
7) NOTE: Before installing the i-6W, set the two position switch on the rear of the speaker to
either the 0 dB or the +3db position. The zero position maintains a flat, even frequency
response, while the +3db position will increase the sound output to the tweeter.The +3dB
position is to be used in rooms with excessive sound absorption material such as thick carpet,
drapes, couches, etc.
8) The i-6W speaker installs in two stages. First remove the speaker from the bezel, by removing
the 6 screws found on the front of the speaker. Once the screws are removed, separate the
bezel from the baffle.
9) Insert the speaker bezel into the hole, and using a Philips screwdriver, tighten the screws
attached to the dog clamps until firm.
DO NOT OVERTIGHTEN
10) Once the bezel is installed, install the speaker into the mounting bezel and using a Philips
screwdriver, tighten the screws until firm. DO NO
T OVERTIGHTEN
PAINTING THE BEZEL AND GRILLE
If you wish, you can paint the speaker bezel and grille to match the décor and design of your
home.
1) For the in wall model, simply separate the bezel from the speaker baffle and paint the bezel,
before you install the speaker portion. The grille is easily separated and can be painted on its
own.
2) For the in ceiling models, use the wall template as a paint mask. Carefully cut the marked line
on the template to create a template that fits inside the bezel, designed to help facilitate
painting. Insert the paint mask, paint the bezel, and then remove the mask when the paint is
dry.
NOTE: If you paint the speaker grilles, ensure that the holes are still open allowing sound to
come through. If any holes become filled with paint, find a small sharp tool and carefully
remove the paint before completing the installation.
FINE TUNING THE SPEAKERS
To fine tune the speakers, you can adjust the angle of the tweeter slightly to direct the sound
towards the seating positions.This option is offered in order to compensate for poor mounting
locations.
Caution: Be extremely careful when adjusting the tweeter as it is very easy to touch the
tweeter, and cause permanent damage which is not covered under the manufacturers
warranty. Do not touch the tweeter in any way.
We sincerely hope you enjoy your new speakers for a lifetime!