Maxxsonics PZI Stereo Amplifier User Manual


 
PZi1000.1 / PZi1500.1 / MONO AMPLIFIER APPLICATIONS
PZi2000.1D / PZi3000.1D / D-CLASS MONO AMPLIFIER APPLICATIONS
7
Basic application
Crossover frequency control checklist:
These sub bass amplifiers can be used any of the bi-amplification systems
LOW PASS: 40Hz to 150Hz
described in this manual, replacing the 2 channel amplifiers as per the
illustrations.
SUBSONIC:15 Hz to 55 Hz
BASS EQ: 0 to +12dB
Interconnect cable checklist:
PHASE: 0 to 180 degrees
Connect the inputs to a suitable source, e.g. a head unit with good quality RCA
cables. Connect the LINE OUT to the inputs of the system highs amplifier.
Level control checklist:
Use at least #12 gauge speaker wiring. The amps have dual speaker terminals,
Refer to the section “Setting up systems after installation for best performance”
simplifying the hookup of multiple speakers
Minimum final loudspeaker impedance: 1-Ohm.
FULL RANGE
STEREO LINE INPUT
NOT USED
Y-ADAPTOR
Note: You can use the Radio/CD designated mono line output
or a full range stereo line output. For full range stereo line output,
you will need an optional “Y-Adaptor” as shown
TO BATTERY +12 Volts
+
+
+
R
-
--
PARALLEL MONO
SUBWOOFERS
2-OHMS EACH MINIMUM
GND REM +12V
POWER INPUT FUSE
SPEAKER OUTPUT
+ + - -
INPUT OUTPUT
LOW SUB BASS
REMOTE
CONTROL
POWER
PROTECT
R R
L L
5V 0.2V 40Hz 150Hz 15Hz 55Hz 0dB 12dB
LEVEL PASS SONIC BOOST
REMOTE TURN-ON
CHASSIS GROUND
DESIGNATED MONO
OUTPUT FROM HEAD UNIT
MONO
SUBWOOFER
0dB 18dB
PZiR-1
Basic application
Crossover frequency control checklist:
These sub bass amplifiers can be used any of the bi-amplification systems
LOW PASS: 35Hz to 250Hz
described in this manual, replacing the 2 channel amplifiers as per the
illustrations.
SUBSONIC:15 Hz to 35 Hz
BASS EQ: 0 to +10dB
Interconnect cable checklist:
PHASE: 0 to 180 degrees
Connect the inputs to a suitable source, e.g. a head unit with good quality RCA
cables. Connect the LINE OUT to the inputs of the system highs amplifier.
Level control checklist:
Use at least #12 gauge speaker wiring. The amps have dual speaker terminals,
Refer to the section “Setting up systems after installation for best performance”
simplifying the hookup of multiple speakers
Minimum final loudspeaker impedance: 1-Ohm.
FULL RANGE
STEREO LINE INPUT
NOT USED
Y-ADAPTOR
Note: You can use the Radio/CD designated mono line output
or a full range stereo line output. For full range stereo line output,
you will need an optional “Y-Adaptor” as shown
TO BATTERY +12 Volts
+
+
+
R
-
-
-
PARALLEL MONO
SUBWOOFERS
2-OHMS EACH MINIMUM
GND REM +12V
POWER INPUT FUSE
SPEAKER OUTPUT
+ + - -
INPUT OUTPUT
LOW SUB BASS
REMOTE
CONTROL
POWER
PROTECT
R R
L L
5V 0.2V 40Hz 150Hz 15Hz 55Hz 0dB 12dB
LEVEL PASS SONIC BOOST
REMOTE TURN-ON
CHASSIS GROUND
MONO
SUBWOOFER
0dB 10dB
PZiR-1
L
R
L
R
9V 0.2V 0 180 0dB 12dB 15 35Hz 35 250Hz PRO
INPUT OUTPUT BALANCED LEVEL PHASE REMOTE BASS EQ SUBSONIC LOW PASS PWR
INPUT
GND REM +12V
POWER
SPEAKER
- - + +
DESIGNATED MONO
OUTPUT FROM HEAD UNIT