Filter
Top Products
6
English
English
TAPE DECK OPERATION
Control used for operating the tape deck.
TAPE PLAYBACK
1. Set the INPUT SELECTOR switch
AA
AA
A to TAPE or CD-R/MD.
2. Play a prerecorded tape on the tape deck.
3. Adjust the volume with the VOLUME control
BB
BB
B.
4. Adjust the tone with the BASS and TREBLE controls
CC
CC
C.
TAPE RECORDING
The playback sound of a program source component, such as a
turntable, a tuner, or a CD player, can be recorded on tape as
follows.
1. Set the INPUT SELECTOR switch
AA
AA
A to the program source
to be recorded.
2. Play the program source.
3. Operate the tape deck(s) to record the playback sound on
tape(s).
Using REC SELECTOR switch
The REC SELECTOR switch is used when copying a cassette
tape to another tape or recording a CD onto a cassette tape.
1. When the switch is in the OFF position, the signal is not output
at the REC OUT jacks.
It is not necessary to output the signal at the REC OUT jacks
when the signal is not recorded onto tape.
By setting the switch to OFF, the signal path inside the unit can
be shortened and crosstalk, etc., can be reduced.
2. In the SOURCE position, the signal selected with the INPUT
SELECTOR switch can be recorded onto tape.
3. In the TAPE COPY positions, the TAPE signal can be re-
corded onto CD-R/MD or vice versa.
4. In the TAPE COPY position, the program source selected with
the INPUT SELECTOR switch can be monitored through the
speakers.
OPERATION PROCEDURES
Operate each equipment to start play.
TO PLAY AN ANALOG DISK
1. Set the INPUT SELECTOR switch q to PHONO.
2. Play a disk on the turntable.
3. Adjust the volume with the VOLUME control w and adjust the
tone with the BASS and TREBLE controls e.
NOTES:
¡ Set the VOLUME control to the minimum position before
placing the stylus on the disk or before replacing the cartridge.
¡ Do not apply shock or vibration to the turntable during play, as
this may cause the stylus to jump and the analog disk to be
damaged.
¡ If the turntable is installed too close to the speakers, the
volume may not be able to be increased to a high level due to
howling.
¡ Do not switch the power OFF while the stylus is on the disk
surface.
TO LISTEN TO FM/AM BROADCASTS
1. Set the INPUT SELECTOR switch q to TUNER.
2. Tune in the desired station on the tuner.
3. Adjust the volume with the VOLUME control w and adjust the
tone with the BASS and TREBLE controls e.
TO PLAY A COMPACT DISC
1. Set the INPUT SELECTOR switch q to CD.
2. Play a CD on the CD player.
3. Adjust the volume with the VOLUME control w and adjust the
tone with the BASS and TREBLE controls e.
TO PLAY A COMPONENT CONNECTED TO AUX JACKS
The component connected to the AUX jacks on the rear panel
can be played as follows.
1. Set the INPUT SELECTOR switch q to AUX.
2. Play the component connected to the selected input.
3. Adjust the volume with the VOLUME control w and adjust the
tone with the BASS and TREBLE controls e.
INTEGRATED AMPLIFIER PM4000
PHONO CD TUNER AUX TAPE CD-R/MD
MUTETONE DEFEAT
MAXMIN
VOLUMEINPUT SELECTOR
PHONESPOWER ON/OFF STANDBY
ON
OFF
ON
OFF
LOUDNESS
ON
OFF
AUXCOPY
TUNERTAPEfiCD-R
CDCD-RfiTAPE
PHONOSOURCE
REC SELECTOR
OFF
BASS TREBLE
1
2SPEAKERS
–+ –+
BALANCE
LR
e
wq
INTEGRATED AMPLIFIER PM4000
PHONO CD TUNER AUX TAPE CD-R/MD
MUTETONE DEFEAT
MAXMIN
VOLUMEINPUT SELECTOR
PHONESPOWER ON/OFF STANDBY
ON
OFF
ON
OFF
LOUDNESS
ON
OFF
AUXCOPY
TUNERTAPEfiCD-R
CDCD-RfiTAPE
PHONOSOURCE
REC SELECTOR
OFF
BASS TREBLE
1
2SPEAKERS
–+ –+
BALANCE
LR
C
BA
REC SELECTOR
AUXCOPY
TUNERTAPEfiCD-R
CDCD-RfiTAPE
PHONOSOURCE
REC SELECTOR
OFF