Mackie MR8 Headphones User Manual


 
9
Owner’s Manual
Owner’s Manual
Appendix A: Service Information
No Sound
Is the Running Man logo [8] on the front panel
illuminated? If not, refer to “No Power” to the left.
Is the input level [6] control turned up?
Is the signal source turned up? Make sure the signal level
from the mixing console (or whatever device
immediately precedes the studio monitor) is high
enough to produce sound.
If it’s a stereo pair, try switching them around. For
example, if a left output is presumed dead, switch the
left and right cords at the monitor end. If the problem
switches sides, it’s not the monitor. It could be a bad
cable, or no signal from the mixer.
Bad Sound
Is the input connector plugged completely into the jack?
If using a
1
4" plug, make sure it is plugged all the way in.
Is it loud and distorted? Reduce the signal level at the
mixer.
If possible, listen to the signal source with headphones
plugged into the preamp stage. If it sounds bad there,
it’s not the monitor.
Too much bass or not enough bass? Move around the
room and see if the bass response changes. It’s possible
your listening position coincides with a room mode
where the low frequencies either become exaggerated
or nulled. If so, try moving the monitors to a different
position, or moving your listening position.
Noise/Hum/Buzz
Check the signal cable between the mixer and the
monitor. Make sure all connections are secure. These
problems usually produce crackling noises, hum, or buzz.
If connecting an unbalanced output to the
MRmk3
studio monitor’s
balanced input, make sure the shield
is connected to the unbalanced ground of the source
and to pins 1 and 3 of the XLR.
If a CATV cable is connected to the system, try
disconnecting it. If the hum goes away, call your cable
carrier to check for proper grounding of the cable.
Make sure the signal cable is not routed near AC cables,
power transformers, or other EMI sources (including
wall warts and line lumps!). These sources usually
produce hum.
Is there a light dimmer or other triac-based device on
the same AC circuit as the monitor? Dimmers cause
buzzing noises. Use an AC line filter or plug the monitor
into a different AC circuit.
Excessive hiss is an indication of an incorrect gain
setting somewhere before the speaker.
If possible, listen to the signal source with headphones
plugged in. If it sounds noisy there, it’s not the monitor.
If you think your
MRmk3 Studio Monitor
has
a problem, please check out the following
troubleshooting tips and do your best to confirm
the problem. Visit the Support section of our website
(www.720trees.com) where you will find lots of useful
information such as FAQs and other documentation.
You may find the answer to the problem without having
to send your
MRmk3
away.
Troubleshooting
No Power
Our favorite question: Is it plugged in?
Make sure the power cord is securely seated in the IEC
socket [1] and plugged all the way into the AC outlet.
Make sure the AC outlet is live (check with a tester or
lamp).
Is the power [2] switch on the rear panel in the ON
position?
Is the Running Man logo [8] on the front panel
illuminated? If not, make sure the AC outlet is live.
If so, refer to “No Sound” below.
If the power indicator is not illuminated, and you are
certain that the AC outlet is live, it is possible the fuse
has blown.
To remove and replace the fuse:
1. Disconnect the power cord from the IEC socket.
2. Remove the fuse drawer by prying it open with a
small screwdriver. It will slide all the way out.
FUSE
3. Remove the fuse and replace it with an
equivalent-type fuse.
115 VAC: T 1 AL / 250 V
230 VAC: T 500 mAL / 250 V [MR5mk3]
115 VAC: T 1.25 AL / 250 V
230 VAC: T 625 mAL / 250 V [MR6mk3]
115 VAC: T 2 AL / 250 V
230 VAC: T 1 AL / 250 V [MR8mk3]
4. Replace the fuse drawer by pushing it all the way
back into the IEC socket.
If two fuses blow in a row, then something is very wrong.
See the “Repair” section on the next page to find out
how to proceed.