Filter
Top Products
6
MR5mk3 / MR6mk3 / MR8mk3
MR5mk3 / MR6mk3 / MR8mk3
Rear Panel Description
Press the right side of this switch down to put the
speaker into standby mode. It will not function, but
the circuits are still live. To remove AC power, either
turn off the AC supply, or unplug the power cord from
the speaker and the AC supply.
3. Signal Inputs
Connect the line-level signal from the mixer
(or other signal source) to one of these input jacks.
There are three types of input connectors to choose
from: balanced XLR, balanced 1/4-inch, and unbalanced
RCA. Since all three of them are connected together
electrically, do not connect more than one signal at a
time to the input jacks.
A balanced signal provides better noise rejection
and is the preferred method, especially if using a cable
longer than 20 feet (6 meters).
They are wired as follows, according to standards
specified by the AES (Audio Engineering Society):
Balanced XLR
Hot (+) Pin 2
Cold (–) Pin 3
Shield (Ground) Pin 1
Balanced 1/4" TRS
Hot (+) Tip
Cold (–) Ring
Shield (Ground) Sleeve
Unbalanced RCA
Hot (+) Tip
Shield (Ground) Sleeve
For more information on these connectors, see
Appendix B on page 11.
2
3
1
SHIELD
COLD
HOT
SHIELD
COLD
HOT
3
2
1
Balanced XLR Connectors
SLEEVE
TIP
SLEEVE
TIP
RING
RING
TIP
SLEEVERING
Balanced 1/4" Connectors
TIPSLEEVETIPSLEEVE
RCA Unbalanced Connectors
This is where the signal is connected to the monitor
and adjustments are made to the frequency response of
the speakers to match the monitor’s location and the
room’s environment.
1. Power Connection and Fuse
Connect the power cord to this IEC socket securely,
and plug the other end into a live AC outlet. Make sure
the AC outlet has the correct voltage indicated next to
the IEC socket
.
Disconnecting the plug’s ground pin is
dangerous. Don’t do it!
The fuse is located behind the fuse cover, at the
bottom of the IEC socket. See the “Troubleshooting”
section on page 9 for information about replacing the
fuse.
2. Power Switch
Press this switch left to turn the
MRmk3 studio
monitor
on. Make sure the level control [6] is down
before you turn it on.
When the power switch is turned
on and the MRmk3 studio monitor is plugged into an
AC outlet, the Running Man logo on the front of the
monitor illuminates to let you know that it’s ready to go.
LOW FREQ
FILTER
HIGH FREQ
FILTER
0–2dB +2dB+2dB0 +4dB
(NORMAL)(NORMAL)
LEVEL
OFF MAX
U
(BALANCED)
XLR
(BALANCED)
TRS
(UNBALANCED)
RCA
INPUTS
CAUTION: REPLACE WITH THE SAME FUSE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
ON
POWER
SETTINGS
REVISION
SERIAL NUMBER
WARNING:
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
N'OUVREZ PAS LA COUVERTURE. N'EXPOSEZ
PAS CET ÉQUIPEMENT À LA PLUIE OU À L'HUMIDITÉ.
2
3
3
3
4 5
7
6
1