Mackie M4000 Stereo Amplifier User Manual


 
7
Owner’s Manual
Owner’s Manual
Hookup Diagrams
M-Series Power Amplifier: Biamp Connection Using Built-in X-over
This drawing shows a typical stereo hookup, connecting
two speakers to the Speakon® outputs. The Amp Mode
switch is set to STEREO, and the X-over switches are set
to FULL. The binding posts can also be used to connect
the speakers (shown as an optional connection).
M
.
4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
+
+
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
1
2
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4 LOAD MIN
2600W BRIDGE
8 LOAD MIN
~120VAC 60Hz 1600W
INPUT
INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
FROM MIXING CONSOLE
MAIN OUT
Biampable Two-Way Speaker
Ch 1 and 2 on single
4-conductor
speaker cable
AMP MODE SWITCH
STEREO
X-OVER SWITCHES
CH 1: LPF CH 2: HPF
1+/–
2+/–
COLD
COLD
AMPLIFIER
END
SPEAKER
END
HOT
CHANNEL 1
CHANNEL 2
1+
1–
2–
2+
1+
1–
2–
2+
M
.
4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
+
+
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
1
2
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4 LOAD MIN
2600W BRIDGE
8 LOAD MIN
~120VAC 60Hz 1600W
INPUT
INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
BRIDGE
+
+
+
SPEAKER OUTPUTS
FROM MIXING CONSOLE
LEFT AND RIGHT MAIN OUT
AMP MODE SWITCH
STEREO
Passive Speakers (Mackie S408)
TO SPEAKERS
OPTIONAL CONNECTION USING BINDING POSTS
M-Series Power Amplifier: Stereo Mode Connection
The Channel 1 Speakon output connector
has four conductors and carries both
channels (1± is Channel 1 out and 2± is
Channel 2 out). This is ideal for driving
a biampable two-way speaker cabinet.
The Amp mode switch is set to STEREO,
Channel 1’s input is jumpered over to Channel 2 using
the Thru connector on Channel 1. The X-over switch on
Channel 1 is set to LPF while Channel 2 is set to HPF.
Channel 1 carries the low frequencies (below 150 Hz) to
the low-frequency driver, and Channel 2 carries the high
frequencies (above 150 Hz) to the high-frequency driver.
Many biampable cabinets are configured to accept both
LF and HF signals on a single Speakon connector.