Filter
Top Products
INSTR,INSTL,DXS-32/EC
LINEAR P/N: 216304 B
MATERIAL: 20 LB. MEAD BOND
SIZE: 8.500" X 11.000"
INK: BLACK
SCALE: 1-1
SIDE 2 OF 2
EXAMPLE INSTALLATIONS TRANSMITTER MOUNTING
ADJUSTING MAGNET HEIGHT PROGRAMMING RECEIVER
CHANGING BATTERIES INTERNATIONAL WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date
is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s
normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling
dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation
for consequential damages arising out of or in connection with use or performance of this product or other indirect damages
with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties,
including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as
labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied.
For warranty service on Linear equipment return product, at sender’s expense to:
Linear Hong Kong
19/F Hounor Industrial Centre
6 Sun Yip Street
Chai Wan, Hong Kong
Attention: Repairs Department
REPAIRS POLICY
✶ Charges will be made for equipment that is not in warranty, shows customer abuse, or is damaged by the effects of lightning,
water, fire, or other abnormal happenings.
✶ Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured equipment at Linear’s
discretion.
✶ The customer is always responsible for shipping and handling charges to the repairs facility. Linear will pay return shipping and
handling charges on “in warranty” products shipped back to the customer. The customer will be billed for the return shipping
and handling charges on “out of warranty” products.
✶ There will be a 50% expedite fee for any express requests.
✶ The International Sales Manager must be notified prior to the return of product to Linear. All international returns must have an
International Repair Authorization number (IRA#). The number must be marked on all packages. Failure to do so will cause
delays in processing.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there
are some limitations which must be observed.
✶ The radios are required to comply with local rules and regulations as radio devices. As such, they have limited transmitter
power and therefore limited range.
✶ A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or
near their operating frequencies, regardless of code settings.
✶ Changes or modifications to the device may void regulatory compliance.
✶ Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
Copyright © 2003 Linear Corporation 216304 B
TRANSMITTER
MOUNTED ON
DOOR JAMB
(NOTE: SMALL END
OF TRANSMITTER UP)
(NOTE: SMALL END
OF TRANSMITTER DOWN)
MAGNET
MOUNTED
ON DOOR
MAGNET MOUNTED
ON DOOR
TRANSMITTER
MOUNTED ON
WINDOW SILL
MAGNET MOUNTED
ON WINDOW FRAME
SLIDING WINDOW
LEFT OPENING DOOR
RIGHT OPENING DOOR
TRANSMITTER
MOUNTED ON
DOOR JAMB
TRANSMITTER
MOUNTED ON
WINDOW FRAME
MAGNET
MOUNTED
ON WINDOW
SASH STILE
DOUBLE-HUNG WINDOW
ATTACH BOTTOM CASE
USING THE SCREWS OR
DOUBLE-STICK TAPE PROVIDED
NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK
TAPE IS NOT ALLOWED IN UL INSTALLATIONS
ADJUST MAGNET
HEIGHT UNTIL
CASE LEVELS
ARE ABOUT EQUAL
TRANSMITTER
MAGNET
THE SNAP-ON MAGNET SPACER
CAN BE USED TO ADD 0.5 cm HEIGHT
TO THE MAGNET (SPACERS CAN ALSO
BE SNAPPED TOGETHER FOR MORE LIFT)
R&TTE VAEE 27836, EMC, SFT, ETS
Linear Corporation declares that the apparatus DXS-32/EC complies with the essential
requirements and other relevant provisions of Directive 1995/5/EC.
PROGRAMMING:
1. PLACE RECEIVER INTO PROGRAM
OR "LEARNING" MODE
2. ACTIVATE TRANSMITTER BY
OPENING DOOR OR WINDOW
3. VERIFY THAT THE RECEIVER
ACCEPTED THE SIGNAL
TESTING:
1. PLACE RECEIVER INTO TEST MODE
2. OPEN DOOR, VERIFY THAT THE
RECEIVER INDICATES AN OPEN DOOR
3. CLOSE DOOR, VERIFY THAT THE
RECEIVER RECOGNIZED THAT THE
DOOR IS CLOSED
OPEN
DOOR
1
SLIDE OLD BATTERIES
OUT OF BATTERY
HOLDERS
2
3 4
DISCARD OLD
BATTERIES
PROPERLY
INSERT TWO TYPE 2032
BATTERIES
PLUS (+) SIDE UP
INTO BATTERY HOLDERS
SEAT BATTERIES COMPLETELY
INTO HOLDERS
BE SURE BATTERIES ARE
NOT TOUCHING EACH
OTHER