Filter
Top Products
VOLUMEMID HIGHLOW BASSBALLS VOLUME
AUX
INPUT
LINE OUT GUITAR
INPUT
POWER
LEAD CHANNEL
RHYTHM CHANNEL
DIGITALEFFECTS
LEVEL PROGRAM
Quad 100 HD
5
6
7
8
2
3
4
1
BIGGER
BALLS
CHANNEL
SELECT
EFFECTS
ON
OFF
ON
OFF
LEAD
RHYTHM
1. HALLREVERB
2. SPRINGREVERB
3. SLAPBACK
4. DELAY
6. CHORUS/REVERB
7. FLANGE/REVERB
5. CHORUS
8. TREMOLO
MIDDLE TREBLE
PREAMP
LEAN
FAT
PREAMP
PUNCH
GRIND
1
3
5
6
789
16
42
10 11
12
13
14
15
17
1918
20
21 22
23
1.) Line Output -
2.) CD/Tape Input -
3.) Guitar Input Jack -
4.)
5.) Bigger B.A.L.L.S.-
6.) Low -
7.) Mid -
8.) Preamp Select Switch-
9.) High -
10.) Lead Channel On LED -
11.) Volume -
12.) Channel Select Switch -
13.) Bass -
14.) Middle -
15.) Preamp Switch -
16.) Treble -
17.) Rhythm Channel On LED -
18.) Volume -
19.) Effects On/Off -
20.) Effects Level -
21.) Program Select -
22.) Jewel Light -
23.) Power Switch -
Back Panel - (not pictured)
Speaker Out -
Line Output -
Effects Loop I/O -
Footswitch Jack -
this is a 3 cond. XLR output jack for plugging into Lo-Z microphone inputs as found on PA or
recording mixers. It is intended in place of external mics or used as a built in direct box.
this 1/4" 3 conductor jack will allow you to plug in a CD player, tape or any other source to practice
along with. It sums the left and right signals into a mono signal. To control the volume of the source, adjust the output
volume of the device.
this is a 1/4" 2 conductor input jack for plugging in your instrument. It is intended for guitars but
will accept other instruments as well.
this switch will add more distortion to the lead channel.
this control is the bass control for the lead channel. It is passive and set to shelve frequencies at 100 Hz.
Turning it fully clockwise, the signal is unaltered. Turning it counterclockwise, the low will be rolled off -12db.
this control is the midrange control for the instrument channel and is passive and set to shelve frequencies at
800Hz.Turning it fully clockwise, the signal is unaltered. Turning it counterclockwise, the low will be rolled off -12db.
this switch selects which preamp style you are using. It will switch between the PUNCH and
GRIND.
this is the high frequency tone control for the microphone channel. It is passive and set to shelve frequencies
at 3KHz. Turning it fully clockwise, the signal is unaltered Turning it counterclockwise, the highs will be rolled off -
12db.
when this LED light is on, it indicates that the Lead Channel is on.
this is a volume control for the Lead Channel ONLY.
this switch selects between the Lead or Rhythm Channel.
this control is the bass control. It is passive and set to shelve frequencies at 100Hz. Turning it fully clockwise,
the signal is unaltered Turning it counterclockwise, the low will be rolled off -12db.
this control is the midrange control for the instrument channel, and is passive and set to shelve frequencies
at 1KHz. Turning it fully clockwise, the signal is unaltered. Turning it counterclockwise, the low will be rolled off -
12db.
when engaged, this switch will boost the treble sound of the Rhythm channel. It boosts 3 KHz by
+6 db.
this is the high frequency tone control. It is passive and set to shelve frequencies at 3KHz on the instrument
channel. Turning it fully clockwise, the signal is unaltered. Turning it counterclockwise, the highs will be rolled off -
12db.
when this LED light is on, it indicates that the Rhythm Channel is on.
this is a volume control for the Rhythm Channel ONLY.
this switch engages the digital effects section.
this control adds the digital effects section and mixes it into the main signal buss. Several different
effects are available.
this switch will select any of eight different effects. 2- Reverbs, 2- Echos, Chorus, Chorus/Reverb,
Flange/Reverb and Tremolo.
this jewel light lets you know that the amplifier is on.
this switch turns on and off the AC power to the amp.
these are 2 conductor 1/4" speaker output jacks. Rating is 4 ohms total. If using both jacks, a load
lower than 8 ohms per jack is not recommended. If using one jack, a load lower than 4 ohms is not recommended.
this is a 2 conductor 1/4" line output jack. This will allow an external amplifier or mixing board to be
supplied with the signal from this amp.
This is an effects Insert jack. Tip send (preamp out) and ring return (power amp in).
this is a 3 conductor 1/4" jack. This is for hooking up a footswitch to switch channels and to turn
on/off the effects section.
B.A.L.L.S. (Ballistic Audio Loudness Level Saturation)- adjust this clockwise to increase the amount of distortion
you Add lower ranges of the control, you get a less distorted sound, a "bluesy"tone .As you increase the gain, you
add Tremendous amounts of distortion to the signal for a harder edged "crunch"tone.