Filter
Top Products
Important Safety Instructions:
1) Read these instructions.
2) Keep these instructions.
3) Read all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade or the third prongs are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, exercise caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when not used for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15).Under no circumstances should the output terminals of the amplifier be short-
circuited.
16).Be sure that the loudspeakers connected can handle the output power of the
amplifier at the loudspeakers rated impedance. The warranty on the amplifier does not
cover damage to loudspeakers that have inadequate power handling capabilities.
17) Where an all-pole MAINS SWITCH is used as the disconnect device, the location
on the apparatus and the function of the switch shall be described, and the switch shall
remain readily operable.
18) A push button is used to turn the power off and on.
19) A LED is used to show when the apparatus is powered on.
CAUTION: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
WARNING: This product may contain chemicals, including lead, known to
the State of California to cause birth defects or other reproductive harm.
Wash hands after handling.
Hum and noise
In most cases, one of the following suggestions should help you
solve a hum noise in your system. Please try these steps in the
order shown; proceeding from one step to the next if the prior
suggestion does not eliminate the problem.
Suggestion #1
To determine if a cable TV connection is responsible for the hum, first turn off all
the components. Disconnect the cable TV feed to your system at the first place
where it connects to your components. Alternatively, disconnect the cable TV
wire where it is connected at the wall outlet. Turn your system back on, and
listen if the hum has disappeared. If removing the cable TV feed has eliminated
the hum, you will need to insert a Ground Loop Isolator (Knoll model GB634)
before reconnecting the cable TV feed, or contact your cable TV operator to see
if they can better isolate your cable feed.
Suggestion #2
Turn off all components in your system and then disconnect the input cables at
the amplifier. Turn the amplifier back on to see if the hum is still present. If the
hum disappears, the fault may be in the input cables used. Try replacing them
with cables that have better shielding, and make certain that the input cables
are not running on top of any AC power cords. Change the cables one at a time
to determine if one or all cables are responsive. If the hum disappears when the
input cables are disconnected but returns after the cables are changed and the
system reconnected, your source device may be causing the problem.
Suggestion #3
Poor grounding of the electrical system in your home may also cause ground
loop problems, particularly when there are multiple components with three
prongs, grounded, power cords. Unplug these components one at a time, and
see if one or all of them is causing the problem. The ultimate solution to this
type of problem is to rewire your house with an isolated, star type-grounding
configuration. Knoll understands that this may be impractical and expensive. In
some instances, the use of an approved AC power isolation transformer of
sufficient capacity may solve this problem.
Warning: If you suspect that the grounding system in your
home’s electrical wiring is causing the hum problem, it is
important that you do not make any changes to the wiring.
Only a licensed electrician should make any changes to
household wiring and they must be made in full compliance
with all local building, safety and electrical codes.