Klipsch SW-112 Speaker User Manual


 
system is completely hooked up. If your receiver does not have a crossover point
setting, set the Lowpass Filter on the subwoofer instead within the same recom-
mended settings (see receiver manual for additional speaker setup info).
“PHASE” 0/180 - This control is used to acoustically match the subwoofer’s
output to your main speakers. Select the position, either 0° or 180°, in which your
subwoofer has more output at the listening position.
“POWER” AUTO/ON/OFF - This is the main A/C power switch for the subwoofer.
This switch must be in the “ON” position for the subwoofer to operate and for
the “AUTO/ON” switch to function. Set this switch to the “OFF” position if the
subwoofer will not be used for an extended period of time (i.e. vacation).
When this switch is in the “AUTO” position, the subwoofer will automatically turn
“on” when it senses a signal. It will automatically turn “off” after 20 minutes with
no signal. When this switch is in the “ON” position, the subwoofer will remain “on”
as long as the “POWER” ON/OFF switch is in the “ON” position. When this switch
is in the “OFF” position, the subwoofer will remain “off” as long as the “POWER”
ON/OFF switch is in the “OFF” position.
Power LED indicator - Located on the front baffle, this LED indicates the operat-
ing status of the built-in amplifier. The LED will light green when the amplifier is
on and receiving a signal. If the LED is dark and not lit, the amplifier is off. For
more information on the controls mentioned in this manual and on bass manage-
ment, see your dealer or visit www.klipsch.com.
CARE AND CLEANING OF YOUR POWERED SUBWOOFER
Your subwoofer has a durable vinyl finish that should only require dry dusting or
cleaning with a dry cloth. Avoid the use of abrasive or solvent-based cleaners and
harsh detergents. The brush attachment of your vacuum should remove any dust
from your subwoofer enclosure.
FCC AND CANADA EMC COMPLIANCE INFORMATION
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not in-stalled and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Approved under the verification provision of FCC Part 15 as a Class B Digital Device.
Caution: Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate this device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The term “IC:” before the radio certification number only signifies that Industry
Canada technical specifications were met.
This equipment complies with FCC and IC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
Le terme «IC:» avant le numéro de certification radio signifie seulement que les
spécifications techniques d’Industrie Canada ont été respectées.
Cet appareil est conforme à FCC et IC l’exposition aux rayonnements limites
fixées pour un environnement non contrôlé. Cet appareil doit être installé et utilisé
avec une distance minimale de 20 cm entre le radiateur et votre corps. Cet trans-
metteur ne doit pas être co-situé ou opérant en liaison avec toute autre antenne
ou transmetteur.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interfer-
ence that may cause undesired operation of the device.
To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that permitted for successful communication.
EU COMPLIANCE INFORMATION:
Eligible to bear the CE mark, Conforms to European Union Low Voltage Directive
2006/95/EC; Conforms to European Union EMC Directive 2004/108/EC and
European Union Directive 2005/32/EC for Ecodesign requirements.
WEEE NOTICE
Note: This mark applies only to countries within the European Union (EU) and Norway.
This appliance is labeled in accordance with European Directive
2002/96/EC concerning waste electrical and electronic equip-
ment (WEEE). This label indicates that this product should not be
disposed of with household waste. It should be deposited at an
appropriate facility to enable recovery and recycling.
PRODUCT REGISTRATION
Register your product online at www.klipsch.com/register
• Klipsch will keep you up-to-date on new products and promotions
• Your personal information will never be resold
• This registration information is not used for warranty purposes.
Please retain your receipt for warranty claims.
Klipsch is a registered trademark of Klipsch Group Inc.