Filter
Top Products
5
OPERATION
IX
PWR PRT
GAIN
0
50Hz11 200Hz 0dB 18dB
X-OVER FREQ BASS BOOST GAIN
0
50Hz11 200Hz 0dB 18dB
X-OVER FREQ BASS BOOST
XOVER
OFF HI LO
AMP2 AMP1
XOVER
OFF HI LO
INPUT
LEVEL
LO
HI
AMP2AMP1
L
R
OUTPUT
POWERAMP1
GNDL+ L– R+ R– REM +12V
AUTO
TURN ON
12V DC AUDIO
OFFSET
FADER
OFF
ON
BRIDGED
AMP2
L+ L– R+ R–
BRIDGED
Automatic Turn-On Selection: The IX series offers three different automatic turn-on modes that can be
selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the
REM terminal to have +12V out for turning on additional amplifi ers.
• Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from your source unit. Run 18
gauge wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the
amplifi er’s positive and negative power terminals. This is the preferred automatic turn-on method.
• DC Offset Turn-On: If Remote Turn-On is not an option, the next best setting is DC Offset. The DC Offset
mode detects a 6V DC offset from the HI-Level speaker outputs when the source unit has been turned on.
• Signal Sense Turn-On: The Audio setting is the fi nal alternative for Automatic turn-on. This is a Signal Sense
turn-on method that detects the incoming audio signal from your source unit and automatically turns on the
amp. This turn-on method will not work properly if the input gain control is not set appropriately.
Fader Switch: Depress the fader switch if you are running two sets of inputs (front and rear for example) to the
amplifi er. Leave the fader switch OFF if you want to drive all channels from a single stereo input.
Input Level: The RCA inputs on KICKER IX amplifi ers are capable of receiving either Hi or Low-level signals from
your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the Input
Level switch on the amplifi er. Refer to the wiring section of this manual for additional instructions.
Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to
the input level of the amplifi er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it
to 25). Next, slowly turn (clockwise) the gain on the amplifi er up until you can hear audible distortion, then turn it
down a little.
Crossover Switch: Use the XOVER switch on the end panel of the amplifi er to set the internal crossover to
OFF, HI or LO. When the switch is set to OFF, a full bandwidth signal will be amplifi ed. Set the switch to HI if
you want the amplifi er’s internal crossover to serve as a high-pass fi lter. Set the switch to LO if you want the
amplifi er’s internal crossover to serve as a low-pass fi lter. Never change the crossover
“OFF/HI/LO” switch setting with the audio system on!
Crossover Control: The variable crossover on the front of the amplifi er allows you to adjust the crossover
frequency from 50–200Hz. The setting for this control is subjective; 80Hz is a good place to start.
Bass Boost Control: The variable bass boost control on the front of the amplifi er is designed to give you
increased output, 0–18dB, at 40 Hz. The setting for this control is subjective. If you turn it up, you must readjust
the input gain control to avoid clipping the amplifi er.
2011 IX 500.4 RevB.indd 52011 IX 500.4 RevB.indd 5 10/12/2010 10:57:26 AM10/12/2010 10:57:26 AM