Filter
Top Products
CT-2050/203/KXF-W6010/W4010 (En/M)
16
Each press of the MODE key changes the setting.
1
“LEVEL” lights up: Recording level setting mode
2
“BAL.” lights up: Recording balance setting mode
3
“BIAS” lights up: Recording bias setting mode (Deck B of the
CT-2050/KXF-W6010 only)
4
“LEVEL”,“BAL.”,and “BIAS”go off: Counter display mode
Set the recording level.
÷Adjust the recording level so that the 0 dB of the peak level indicators
sometimes lights up.
÷The recording level can be adjusted on both decks A and B. (CT-203/
KXF-W4010; Deck B only)
lights up
lights up
The cassette deck incorporates the Dolby HX Pro headroom
extension function and auto-bias function to provide a re-
cording with superior high-frequency characteristics.
Since this unit is not designed for recording with metal
(TYPE
) tapes, do not use metal tapes for recording.
How to record (CT-203/KXF-W4010; Deck B only)
Preparation
÷Select by operating the input selector of the amplifier (optional).
÷ In case of recording a FM broadcast,refer to discription of "How to use
the MPX FILTER key". &
÷While pressing the PAUSE (8) key, press the REC/ARM (¶) key.
0dB.
Recording level display.
1
Make “Playback (recording) preparation”.
0
(CT-203/KXF-W4010; Insert a tape in deck
B.)
2
(Load a disc in the CD player.)
: Keys and control used in the operations described on this page.
Normal recording
1
Select the source to be recorded.
3
2
Perform auto-bias adjustment. (The bias adjustment is applied to deck B.)
AUTO BIAS
÷The optimum bias is set in about 40 seconds, after which the deck
enters the stop mode.
÷For a fine adjustment after setting AUTO BIAS, refer to the description
of “Bias level adjustment”. (CT-2050/KXF-W6010 only) &
÷To cancel the auto-bias adjustment operation in the middle, press the
stop (7) key.
÷÷
÷÷
÷Recording is possible even when the auto-bias setting is omitted.
÷If the amount of remaining tape is small, the auto-bias adjustment may
be canceled in the middle and tape stopped at that position.
÷The bias level is canceled when the eject (0) key is pressed.
1
Play a music source.
2
Enter the record-pause mode.
8
PAUSE
¶
REC/ARM
3
Press the MODE key and select the "BAL."
mode.
MODE
4
Adjust the recording balance.
REC LEVEL/BAL.
/BIAS
∞
MAX/R
∞
MIN/L
Right sound
decreases.
Left sound
decreases.
5
Press the MODE key and select the
"LEVEL" mode.
MODE
6
Adjust the recording level.
REC LEVEL/BAL.
/BIAS
∞
MAX/R
∞
MIN/L
Recording
level
decreases.
Recording
level
increases.
7
Stop playing the source.
÷In counter, adjust the recording balance level so that the left and right
displays are the same. You can also check with the Ò and  peak level
indicators.
Right channel levelLeft channel level
CT-2050/KXF-W6010
CT-203/KXF-W4010
CT-2050/KXF-W6010 only
“AUTO BIAS”blinks. After approximately
40 seconds
“AUTO BIAS” lightsup.
Each press of the MODE key changes the setting.
1
“LEVEL” lights up: Recording level setting mode
2
“BAL.” lights up: Recording balance setting mode
3
“BIAS” lights up: Recording bias setting mode (Deck B of the
CT-2050/KXF-W6010 only)
4
“LEVEL”,“BAL.”,and “BIAS”go off: Counter display mode