Kenwood KDC-MP5028 CD Player User Manual


 
10
|
English
General features
System Q
You can recall the best sound setting preset for
different types of music.
1 Select the source to set
Press the [SRC] button.
2 Select the Sound type
Press the [Q] button.
Each time the button is pressed, the sound
setting switches.
Sound setting Display
User memory "USER"
Rock "ROCK"
Pops "POPS"
Easy "EASY"
Top 40 "TOP40"
Jazz "JAZZ"
Natural "NATURAL"
• User memory: The values set on the <Audio Control>
(page 10).
• Each setting value is changed with the <Speaker
Setting> (page 12).
First, select the speaker type with the Speaker setting.
Audio Control
1 Select the source for adjustment
Press the [SRC] button.
2 Enter Audio Control mode
Press the [VOL] knob.
3 Select the Basic Audio item for adjustment
Press the [VOL] knob.
Each time the knob is pressed, the items that can
be adjusted switch as shown below.
4 Adjust the Basic Audio item
Turn the [VOL] knob.
Adjustment Item Display Range
Rear Volume *
1
"R-VOL" 0 — 35
Subwoofer level*
2,3,4
"SW L" –15 — +15
Bass level*
5,6
"BAS L" –8 — +8
Middle level*
5,6
"MID L" –8 — +8
Treble level*
5,6
"TRE L" –8 — +8
Balance "BAL" Left 15 — Right 15
Fader*
4
"FAD" Rear 15 — Front 15
Exit Audio Control mode
• *
1
You can control this item when "2ZON" of <Audio
Setup> (page 11) is set to "ON".
• *
2
You can control this item when <Switching preout>
(page 25) is set to "SWPRE SW". (KDC-MP5028/
MP528 only)
• *
3
You can control this item when <Subwoofer
Output> (page 11) is set to "SW ON".
• *
4
You can control this item when "2ZON" of <Audio
Setup> (page 11) is set to "OFF".
• *
5
These items can be adjusted in detail by the
following methods. (Function of the KDC-X589)
• *
6
Source tone memory: The set up value is put in the
memory per source. (Detail Audio item is included)
5 Exit Audio Control mode
Press any button.
Press the button which is not [VOL] knob and
[ATT]/ [ANG] button.
Adjust the detail of Audio Control
1 Select the Audio item for adjustment
By referring to the step 1 — 3 above, select the
desired item to be set in detail from the items
marked with *
5
.
2 Enter Detail adjustment mode of Audio
Control
Press the [VOL] knob for at least 1 second.
3 Select the Detail Audio item for adjustment
Press the [VOL] knob.
Each time the knob is pressed, the items that
can be adjusted switch as shown below.
4 Adjust the Detail Audio item
Turn the [VOL] knob.
Bass level
Adjustment Item Display Range
Bass Center Frequency "BAS F" 40/50/60/70/80/100/
120/150 Hz
Bass Q Factor "BAS Q" 1.00/1.25/1.50/2.00
Bass Extend "B EX" OFF/ON
Middle level
Adjustment Item Display Range
Middle Center Frequency "MID F" 0.5/1.0/1.5/2.0 kHz
Middle Q Factor "MID Q" 1.0/2.0
Treble level
Adjustment Item Display Range
Treble Center Frequency "TRE" 10.0/12.5/15.0/17.5 kHz