Filter
Top Products
SURROUND
SPEAKERS
LEFTRIGHT LEFTRIGHT
CENTERFRONT
CENTER
FRONT LEFT
FRONT RIGHT
SURROUND RIGHT
SURROUND LEFT
SURROUND BACK
SURROUND
BACK
– 3 –
1
6
5
4
3
2
SP-XF30S
SP-XF30F
Assembling the front and surround speakers
Assembled speakers: With stand: Refer to Steps
1
to
6
Without stand: Refer to Steps
1
to
5
Before assembling—
• Prepare a Philips screwdriver (not supplied).
• Take care not to drop any component part while assembling; otherwise, it may cause damage to the floor or injury.
• Each speaker cord has its name tag attached to one end. Attach the end without the name tag to the speaker terminal.
or
or
With stand
With standWithout stand Without stand
Connections
Connecting the speaker system to the amplifier
Before connecting—
• Turn off the power to the amplifier before connecting the speaker system; otherwise, the speakers may be damaged.
• The impedance of each speaker is 6 Ω. Before connecting them to your amplifier, check the speaker impedance range of your amplifier. If the impedance of this
speaker is out of the speaker impedance range indicated on the amplifier, you cannot connect this system to the amplifier.
• The maximum power handling capacity of the speakers are 100 W. Excessive input will result in abnormal noise and possible damage.
• Be sure to turn down the volume level to prevent unwanted noise before performing following operations:
– Turning on or off other components,
– Operating the amplifier,
– Tuning FM stations,
– Fast-forwarding a tape,
– Continuously reproducing high frequency oscillation or high pitch electronic sounds.
• When using a microphone, do not aim it at the speakers or use it near the speakers; otherwise, the howling which occurs may damage the speakers.
• Before replacing the cartridge, always turn off the power to the turntable; otherwise, the clicking noise may damage the speakers.
Connecting the Center speaker
Press ReleaseInsert
Black striped
Copper
Red
Black
Route the cord
Speaker cord
Base plate
(Rear side)
Speaker cord
Stand (or
speaker directly)
Base plate
Screw—
M5 x 25 mm
(M5 x 1 in.)
Press ReleaseInsert
Black striped
Black
Copper
Speaker
cord
Red
Stand
Speaker
White
Black
Front left
Subwoofer
Amplifier
Surround right
Surround left
Center
Surround back
Front right
Typical connection method to an amplifier
Connect the speakers to the speaker terminals of the amplifier with the
speaker cords by referring to the diagram below.
• Make sure to match the polarity (ª and
·) when connecting the speaker cords.
• The diagram below is an example of a
typical connection.
Connecting the Surround back speaker
Black striped
Copper
Red
Black
Press
ReleaseInsert
Speaker layout
Specification
SP-XF30F (Front speakers)
Type: 2-way 3-speaker Bass reflex type (Magnetically-shielded type)
Speaker unit: 5.5 cm (2
3
/16 in.) cone (× 2), 3.0 cm (1
1
/16 in.) dome
Frequency range: 95 Hz to 40 000 Hz
Input impedance: 6 Ω
Power handling Capacity: 100 W
Sound pressure level: 80 dB/W•m
Dimensions (W × H × D):
250 mm × 1 103 mm × 250 mm
(9
7
/8 in. × 43
7
/16 in. × 9
7
/8 in.)
Mass: 3.67 kg (8.1 lbs) each
SP-XF30S (Surround speakers)
Type: 2-way 3-speaker Bass reflex type (Magnetically-shielded type)
Speaker unit: 5.5 cm (2
3
/16 in.) cone (× 2), 3.0 cm (1
1
/16 in.) dome
Frequency range: 90 Hz to 40 000 Hz
Input impedance: 6 Ω
Power handling Capacity: 100 W
Sound pressure level: 77 dB/W•m
Dimensions (W × H × D):
250 mm × 1 103 mm × 250 mm
(9
7
/8 in. × 43
7
/16 in. × 9
7
/8 in.)
Mass: 3.83 kg (8.5 lbs) each
SP-XF70C (Center speaker)
Type: 2-way 3-speaker Bass reflex type (Magnetically-shielded type)
Speaker unit: 5.5 cm (2
3
/16 in.) cone (× 2), 3.0 cm (1
1
/16 in.) dome
Frequency range: 90 Hz to 40 000 Hz
Input impedance: 6 Ω
Power handling Capacity: 100 W
Sound pressure level: 81 dB/W•m
Dimensions (W × H × D):
209 mm × 85 mm × 92 mm
(8
1
/4 in. × 3
3
/8 in. × 3
5
/8 in.)
Mass: 0.87 kg (2.0 lbs)
SP-XF70S (Surround back speaker)
Type: 2-way 3-speaker Bass reflex type (Magnetically-shielded type)
Speaker unit: 5.5 cm (2
3
/16 in.) cone (× 2), 3.0 cm (1
1
/16 in.) dome
Frequency range: 90 Hz to 40 000 Hz
Input impedance: 6 Ω
Power handling Capacity: 100 W
Sound pressure level: 78 dB/W•m
Dimensions (W × H × D):
84 mm × 211 mm × 120 mm
(3
5
/16 in. × 8
5
/16 in. × 4
3
/4 in.)
Mass: 0.96 kg (2.2 lbs)
– 4 –– 2 –
EN_SP-XF70[J]ff.p65 27/2/04, 10:27 PM2