Filter
Top Products
32
1
Start playing 2 channel software—either Linear
PCM or analogue signal—and select the source.
2
Press SURROUND repeatedly until one of the
DSP modes you want to apply appears on the
display.
The DSP indicator lights up on the display.
• Each time you press the button, the DSP modes change as
follows:
3
Press TEST to check the speakers output
balance.
“TEST L” starts flashing on the display, and a test tone comes out
of the speakers as follows:
Using DSP modes
Once you have adjusted the DSP modes, the adjustment is
memorized for each source.
• You cannot use the DSP modes if no surround speakers are
connected.
• You cannot adjust the effect level for “ALL CH ST.”
When operating this receiver using the remote control,
always set the mode selector to AUDIO/TV/VCR/STB.
Before you start, remember...
Make sure that you have set the speaker information correctly (see
pages 15 to 18).
From the remote control:
CENTER*
1
: To adjust the center speaker output level
(from –10 dB to +10 dB).
SURR L*
1
: To adjust the left surround speaker output level
(from –10 dB to +10 dB).
SURR R*
1
: To adjust the right surround speaker output level
(from –10 dB to +10 dB).
PANORAMA control*
2
:
•
Select “ON” when you would like to enjoy
“wraparound” sound effect with side-wall image.
• Select “OFF” when you would like to hear
originally recorded sound.
*
1
“0” is the initial setting for each speaker setting.
*
2
“OFF” is the initial setting.
6
Turn MULTI JOG to adjust the item selected in
step
5
, then press SET.
Your setting is stored.
• When adjusting the speaker output levels, make adjustments so
that the sound level of the selected speaker is set at the same
level as that of the front speakers.
Ex.: When selecting “+8 (dB)” for “CENTER.”
7
Repeat steps
5
and
6
to adjust the other
settings.
To cancel Surround mode
Press SURROUND repeatedly on the remote control or press
SURROUND then turn MULTI JOG on the front panel so that
“STEREO” appears on the display.
• If Surround mode is canceled while playing back multi-channel
digital software, all channel signals are mixed and output through
the front speakers (and subwoofer if you have connected a
subwoofer and set the subwoofer setting correctly—“USE” for Quick
Setup or “YES” for Manual Setup—see pages 16 and 17).
NOTES
• You can adjust the speaker output levels using the remote control
without outputting the test tone.
• You cannot adjust the center speaker output level and no test tone
comes out of the center speaker when “CNTR SP” is set to “NO.”
• You cannot adjust the surround speaker output levels and no test
tone comes out of the surround speakers when “SURR SP” is set
to “NO.”
• Remember not to change the speaker setting while using any
Surround modes; otherwise, the Surround mode may be canceled
when you deactivate the speakers required for it .
• You cannot use any Surround modes when selecting DVD MULTI
as a playback source.
PL ΙΙ
SUBWFR
VOL
LR
LPCM
SUBWFR
VOL
DSP
LR
LPCM
PLII MOVIE
PLII MUSIC
STEREO
(Surround/DSP off)
(Back to the beginning)
LIVE CLUB
PAVILION
HALL
DANCE CLUB
ALL CH ST.
It will be convenient for you to use
the remote control for the sound
adjustments, since you can make
adjustments from your listening
point, and use the test signal.
Creating realistic sound fields
DVD
AUDIO/TV
/VCR/STB
AUDIO
ZOOM
ANGLE
REPEAT
DIMMER
SUBWFR CENTER L RSURR
BASS BOOST
A.POSITION
SMART S. SETUP
SLEEP CANCEL
SURROUND
ANALOG/DIGITAL
TV RETURN 100
+
BASS TREBLE
SUBTITLE RETURN
TITLE/GROUP
BASS TREBLE
123
4
VFP
INPUT
TONE
TEST EFFECT
DECODE
56
789
10
3D
0 +10
SUBWFR
VOL
DSP
LR
LPCM
TEST L
(Left front speaker)
TEST C
(Center speaker)
TEST R
(Right front speaker)
TEST LS
(Left surround speaker)
TEST RS
(Right surround speaker)
28-34_RX-ES9SL[B]f 03.6.27, 16:4632