Filter
Top Products
2
Subwoofer system (1 amplifier)
2-subwoofer system (2 amplifiers)
2-subwoofer system (1 amplifier)
4-speaker system plus subwoofer—5.1-channel (3 amplifiers)
Connection varies depending on the number of the speakers used in your car. Select the
appropriate connection referring to the following diagrams.
*
1
Not provided for this unit.
*
2
You can connect 2 subwoofers as shown in “Example 1” to “Example 4” below.
*
3
You can connect 2 subwoofers as shown in “Example 2” to “Example 4” below.
*
4
Be sure to connect the line output from the receiver to the left (L) jack on this unit.
SPEAKER CONNECTIONS
Note
Use the subwoofers with an impedance of 2 Ω to 8 Ω.
JVC amplifier, etc.
(purchased separately)
JVC amplifier, etc.
(purchased separately)
Subwoofer*
2
Subwoofer*
2
Subwoofer*
2
Subwoofer*
2
Subwoofer*
3
Subwoofer*
3
Line Out
(Center)
Center Speaker
Note
Use the subwoofer with an impedance of 1 Ω to 8 Ω.
Note
• Use the subwoofers with an impedance of 1 Ω to 8 Ω.
• Incoming signals are emitted through the PRE OUT jacks.
Subwoofer
Out
Before connecting: Securely connect all the parts. If the connections are loose, due to contact
resistance etc., heat will break out and may cause an accident. Secure and cover the cords with
insulating tape and run them under the car mats.
JVC car receiver, etc.
Line Out (Rear)
or
Subwoofer Out
Line Out (Rear)
or
Subwoofer Out
JVC car receiver, etc.
Line Out (Rear)
or
Subwoofer Out
Line Out
(Rear)
Line Out
(Front)
Front Speaker
(left/right)
Rear Speaker
(left/right)
JVC car receiver, etc.
JVC car receiver, etc.
Subwoofer system (2 amplifiers)—External Bridge Mode
Subwoofer*
3
JVC car receiver, etc.
Line Out (Rear)
or
Subwoofer Out
Note
• Use the subwoofer with an impedance of 2 Ω to 8 Ω.
• Use the subwoofer which have sufficient capacity to the unit.
• Make sure to set the EXTERNAL BRIDGE switch as illustrated above; otherwise, the sound
may be distorted.
• You cannot adjust the sound on the amplifiers separately. The adjustment on the amplifier A is
also applied to the amplifier B.
Amplifier A
Amplifier B
Speaker Wire
Note
Use the subwoofer with an impedance of 1 Ω to 8 Ω.
Examples for connecting 2 subwoofers
Example 3
Load impedance: 4 Ω
Example 2
Load impedance: 2 Ω
Example 4
Load impedance: 8 Ω
Example 1
Load impedance: 1 Ω
Subwoofer
(4 Ω)
Subwoofer
(4 Ω)
Subwoofer
(4 Ω)
Subwoofer
(4 Ω)
Subwoofer
(Dual 4 Ω)
Subwoofer
(Dual 4 Ω)
Subwoofer
(Dual 4 Ω)
Subwoofer
(Dual 4 Ω)
EN_KS-AR9501D[JK]-4.indd 2EN_KS-AR9501D[JK]-4.indd 2 08.12.23 4:30:31 PM08.12.23 4:30:31 PM