Filter
Top Products
Parts Identification
7 Front
7 Rear
Left speaker
Right speaker
Power lamp
Headphone jack
Power switch
(volume control) knob
Left speaker
Right speaker
DC IN jack
L SPKR (left speaker) jack
(brown connector)
Line-input cord
(green plug):
2 m (6.5 ft)
Left speaker cord
(brown plug):
2 m (6.5 ft)
Troubleshooting
Check the following if you think the system is not working correctly.
• If the problem should persist, unplug the AC adapter from the AC outlet, and refer servicing
to the qualified service personnel.
Symptom
Power lamp is
turned off.
Power lamp is turned
on, but no sound.
Sound is distorted.
Sound level is too low.
Sound comes out of
only one speaker.
Possible Cause
• AC adapter is not connected.
• No power is supplied.
• Line-input cord is not connected.
• Volume level is too low.
• Volume level is too high.
• Input sound level is too high.
• Input sound level is too low.
• Line-input cord is not connected firmly.
• Left speaker is not connected to the
right speaker.
Remedy
• Plug in adapter firmly.
• Try another AC outlet.
• Plug in the cord firmly.
• Turn up the volume control.
• Turn down the volume control.
• Adjust it to the optimum level.
• Adjust it to the optimum level.
• Plug in the cord firmly.
• Plug in Speaker cord firmly.
Specifications
7 Amplifier: Power output 1.5 W per channel (at 10 % THD)
Input impedance 12 kΩ (nominal)
Input sensitivity 200 mV/1 kHz/1 W
Power supply DC 9 V 500 mA (by AC adapter)
Power consumption 12 W
Signal-to-noise ratio 72 dB
7 Power Requirements: AC 120 V
, 60 Hz
7 Speaker System: Enclosures Plastic molded
Frequency response 100 Hz – 20 000Hz
Speaker uint 90 mm x 50 mm (3-
9
/16 in. x 2 in.) cone type,
magnetically shielded
7 Dimensions (H/W/D): Right speaker: 200 mm x 80.5 mm x 112 mm
(7-
7
/8 in. x 3-
1
/4 in. x 4-
7
/16 in.)
Left speaker: 200 mm x 80.5 mm x 99.3 mm
(7-
7
/8 in. x 3-
1
/4 in. x 3-
15
/16 in.)
7 Mass: Right speaker: 400 g (0.89 lbs) Left speaker: 345 g (0.77 lbs)
* Design and specifications are subject to change without notice.
Connection Diagram
Audio Output (Green connector)
Green plug
(stereo mini:
φ 3.5 mm)
Line input cord
Black plug
AC adapter
(AC 120 V , 60 Hz)
To an AC outlet
After completing all other connections,
plug in the AC adapter.
Brown connector
Brown plug (mini: φ 2.5 mm)
Left speaker cord
Home Docking Cradle for JVC Sirius tuner
Left Speaker
Right Speaker
REAR VIEW
Although the speakers are magnetically shielded, they may affect some monitors if installed
nearby. Should color deterioration occur on a monitor, place the speakers slightly away.
Turn off the monitor, and keep it turned off for about 15 to 20 minutes.
By doing this, normal color will be restored.
Using the Speaker System
1
Connect the speakers and AC adapter as shown in the Connection Diagram.
2
Turn the power switch knob clockwise to turn the power on.
A click sound is heard and the power lamp lights up in green.
3
Turn the power switch knob further to obtain the optimum sound level.
• In case the sound level is not sufficient though the knob is turned up fully clockwise,
increase the output level of the signal source as it may be set too low.
• When using the headphones, plug it into the headphone jack. No sound comes out of the
speakers.
Turn the knob fully counterclockwise before connecting the headphones, not to damage
the speakers and your ears.
To turn off the speakers, turn the power switch knob fully counterclockwise.
• Never turn it on or off by any other means to ensure safe operation of the speakers.
Maintenance
If cleaning is required, disconnect the AC adapter from AC outlet, and wipe off with soft cloth.
For removing heavy stain, use the cloth moistened with neutral detergent.
Do not use inflammable or harmful fluid such as benzine or thinner.
REAR VIEW
CS-SR100_f.p65 04.6.2, 1:51 PM2