JVC CA-MXK1R Speaker System User Manual


 
26
Using the Timers
EnglishEnglishEnglishEnglishEnglishEnglishEnglish
LVT0686-009B / CA-K1R/CA-K3R(B) / English
Using the Unit
You can set the time in the same way as for setting the Daily Tim-
er.
1
Insert a blank or erasable tape into the Deck
B and wind past the tape leader.
2
Press the CLOCK/TIMER button until “ON
TIME” immediately after “REC” appears on
the display.
Then, the "REC" indicator blinks on the display.
Each time you press the button, the display changes as follows:
DAILY = ON TIME = REC = ON TIME* = Clock setting
display = Canceled = (back to the beginning)
* : This item should be selected for the REC Timer setting.
After 2 seconds, the System enters ON-time setting mode. The cur-
rent ON time appears on the display and the hour digits blink.
3
Setting the ON time you want the System to
turn on.
1. Press the 4 or ¢ button to set the hour, then press the
SET button.
2. Press the 4 or ¢ button to set the minute, then press the
SET button.
“OFF TIME” appears for 2 seconds, and the System enters
OFF-time setting mode. The current OFF time appears on the
display, and the hour digits blink.
4
Setting the OFF time you want the System to
turn off.
1. Press the 4 or ¢ button to set the hour, then press the
SET button.
2. Press the 4 or ¢ button to set the minute, then press the
SET button.
The System enter Preset Station Entering mode.
5
Select the preset station for recording.
1. Press the 4 or ¢ button to set the band (TUNER FM or
TUNER AM), then press the SET button.
2. Press the 4 or ¢ button to set the preset number, then
press the SET button.
The REC indicator stops blinking and remains lit.
Each setting you have made appears on the display in the
order of ON time, OFF time, radio band and the preset
number.
6
Press the
%
%%
%
button to turn off the System, if
necessary.
To change the timer setting
, repeat the setting procedure from
the beginning.
When the timer ON-time comes:
When the timer ON-time comes, the System automatically
turns on. The station you have set is played. The Timer indica-
tor ( ) blinks during timer operation.
To stop timer recording, press the 7 button.
When the timer OFF-time comes, “OFF” blinks on the display
just before the OFF-time and the System automatically turns off.
The REC Timer works even if the System is turned on.
Turning the REC (Recording) Timer On and Off
Once you have set the REC Timer to record a source, the timer set-
ting is stored in memory. So, though the REC Timer turns off once
it is used, you can recall it at any time.
To cancel the REC Timer temporarily:
1
Press the CLOCK/TIMER button on the Unit
repeatedly until “REC” appears on the dis-
play.
2
Press the CANCEL button on the Unit.
“OFF” appears and the “REC” indicator goes out.
To activate the cancelled REC Timer:
1
Press the CLOCK/TIMER button on the Unit
repeatedly until “REC” appears on the dis-
play.
The “REC” indicator also blinks on the display.
2
Press the SET button on the Unit.
The “REC” indicator remains lit. Each setting already made
appears on the display in the order of ON time, OFF time, and
the preset number, and then the display returns to the original
display.
CAUTION:
If the System is unplugged, or a power failure oc-
curs, the timer setting will be lost in a few days.
You will need to reset the clock first, then the
timer.
REC
REC
After 2 seconds
MX-K1R&MX-K3R(B).book Page 26 Friday, March 23, 2001 9:49 AM