JVC CA-MXKC2 CD Player User Manual


 
26
English
Troubleshooting
If you are having a problem with your System, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as
your dealer, for service.
Symptom Possible Cause Action
No sound is heard. Connections are incorrect, or loose.
Headphones are connected.
Check all connections and make corrections.
(See pages 4 to 6.)
Disconnect the headphones.
Poor radio reception The antenna is disconnected.
The AM Loop Antenna is too close to the
System.
The FM Wire Antenna is not properly
extended and positioned.
Reconnect the antenna securely.
Change the position and direction of the AM
Loop Antenna.
Extend FM Wire Antenna to the best recep-
tion position.
The disc tray does not open.
The AC power cord is not plugged in.
Tray is locked.
Plug the AC power cord.
Unlock the tray. (See page 15.)
The CD skips. The CD is dirty or scratched. Clean or replace the CD. (See page 25.)
The CD does not play. The CD is upside down. Put the CD in with the label side up.
The MP3 disc does not play.
No MP3 files are recorded on the disc.
MP3 files do not have the file extension —
.MP3, .Mp3, .mP3, or .mp3 in thier file names.
MP3 files are not recorded in the format com-
pliant with ISO 9660 Level 1 or Level 2.
Replace the disc.
The readout time of the MP3 disc is too long. The readout time varies with the complexity of
the recording configuration.
Do not use too many hierarchies and folders
when recording. Also, do not record any other
types of audio tracks together with MP3 files.
(See page 11.)
The cassette holder cannot be opened. During tape playing, the power cord was un-
plugged.
Plug in the power cord, and turn on the System.
Unable to record. Cassette record protect tabs are removed. Cover holes on back edge of cassette with tape.
Unable to operate the Remote Control. The path between the Remote Control and the
sensor on the Unit is blocked.
The batteries have lost their charge.
Remove the obstruction.
Replace the batteries.
Operations are disabled.
The built-in microprocessor has malfunctioned
due to external electrical interference.
Unplug the System then plug it back in.
Amplifier Speaker Specifications (each unit)
MX-KC2 60 W SP-MXKC2/SP-MXKC15
MX-KC15 50 W Type 2-way bass-reflex type
per channel, min. RMS, driven Speaker Unit Woofer: 13 cm (5-1/8") cone
×
1
into 6
at 1kHz, with no more than Tweeter: 5cm (2") cone
×
1
10
% total harmonic distortion Power Handling Capacity 60 W
Input Sensitivity/Impedance (1 kHz)
Impedance 6
AUX IN 400 mV/50 k
Frequency Range 45 Hz - 22 000 Hz
Speaker terminals 6 - 16
Sound pressure level 87 dB/W·m
Phones 32
- 1 k
Dimensions 205 mm
×
308 mm
×
209 mm (W/H/D)
15 mW/ch output into 32
(8-1/8"
×
12-3/16"
×
8-1/4")
Cassette Deck Section
Mass Approx. 2.9 kg (6.4 lbs)
Frequency Response
Accessories
Type I (NORMAL) 63 Hz - 12 500 Hz AM Loop Antenna (1)
Wow And Flutter 0.15% (WRMS) FM Wire Antenna (1)
CD Player
Remote Control (1)
CD Capacity 3 CDs Batteries R6P (SUM-3)/AA (15F) (2)
Dynamic Range 83 dB
Power Specifications
Signal-To-Noise Ratio 85 dB Power Requirements AC 120 V , 60 Hz
Wow And Flutter Unmeasurable Power Consumption 95 W (power on mode)
Tuner
13 W (in Standby mode)
FM Tuner 1.2 W (in ECO mode)
Tuning Range 87.5 MHz - 108.0 MHz
AM Tuner
Design and specifications are subject to change without notice.
Tuning Range 530 kHz - 1 710 kHz
Unit
Dimensions
270 mm
×
308 mm
×
410mm (W/H/D)
(10-11/16"
× 12-3/16"
× 16-3/16")
Mass Approx. 6.5 kg (14.4 lbs)
Specification
LVT1346-001A_E.book Page 26 Wednesday, March 30, 2005 1:16 PM