Filter
Top Products
Dock adaptor
(Supplied with the iPod or
purchased separately)
Power button
VOLUME button
Adjusts the volume level of the Unit.
SNOOZE/BRIGHTNESS button
Pressing this button displays the current time.
* If you press and hold this button while the power is turned on,
the display light turns on and off.
* Even if the power is not supplied to the Unit, the display is lit.
– 2 –
Preparation of the Unit
n
Setting the batteries / AC adaptor
This Unit runs on AA batteries or from the AC adaptor.
To load batteries, open the covers of the battery compartments and
insert AA batteries (not supplied) in the right and left compartments
(four batteries total).
Be sure to match the poles (+/-) correctly.
Read “Safety Precautions” on page 1 thoroughly in order to handle the dry batteries correctly.
CAUTION
n
Setting the time
Set the time with the power off.
1
Press and hold the SOURCE button.
2
Whilethetimedisplayisashing,pressthe
SOURCE button.
* If is ashing, press
4
/
¢
to make the time display ash.
3
Select the time display setting and the current
time.
Use
4
/
¢
to select a number and press the SOURCE
button to enter it. Then, you can select the next item. The
items are switched in the following order.
24-hour display/12-hourdisplay → Hour → Minute → Setting
complete. (The current time is displayed.)
* If you made a mistake or the setting disappeared because of a
power failure or the like, start over from Step 1.
Listening to / Charging the iPod
■ListeningtotheiPod
1
Set the iPod in the Unit.
· Set the dock adaptor and then set the iPod.
· Securely insert the iPod all the way into the adaptor.
* A terminal cover is covering the connecter terminal when you purchase the Unit. Remove
the cover before use.
* If you do not connect the iPod, be sure to cover the connecter terminal with the terminal
cover. Dust or the like may inltrate the Unit and cause malfunctions.
* When you operate the iPod, support the iPod from the back side. Excessive force may
damage the connector terminal.
2
Turn on the power.
When the iPod is selected as the audio source, it automatically starts playback.
3
Select “iPod” with the SOURCE button.
The Unit automatically starts playback.
Button Function
6
Playback / Pause
Press and hold this button to switch the iPod to the sleep mode.
¢
Next song / Fast forward (Press and hold.)
4
Previous song (Press this button during playback to jump back to the
beginning of the track.) / Fast rewind (Press and hold.)
Dock adaptor (Supplied with the iPod or purchased separately)
· You can remove the dock adaptor by pulling up the slot with your ngernail or
a ne-tipped tool.
· Pay attention not to injure your ngertip or damage the connector.
* If a dock adaptor was not supplied with your iPod, purchase a dock adaptor from
Apple Inc. For details, visit Apple’s website. <http://www.apple.com/>
Listening to External Devices
1
Connect an external device to the Unit.
Connect the external device to the AUDIO IN jack on the rear of the unit using a
stereo mini plug cord (not supplied).
To the audio output of a CD/MD/digital
audio player, etc. or headphones terminal
2
Turn on the power.
3
Select “Audio in” with the SOURCE button.
4
Start playback from the external device.
n
Setting the timer
Set the timer with the power off.
1
Press and hold the SOURCE button.
2
Use the
4
/
¢
button to display and press the SOURCE
button.
3
Select the time and so on when to start playback.
Use the
4
/
¢
button to select the setting and press the SOURCE button to enter
it. Then, you can select the next item. The items are switched in the following order.
* If you made a mistake or the setting disappeared because of a power failure or the like, start
over from Step 1.
[Playing back from the iPod]
Hour → Minute → Sound source (iPod) → Volume level when timer playback starts →
Playback time → Setting complete. (The current time is displayed.)
· The last selected track is automatically played back.
· The playback time is set in 5-minute increments from 10 to 30 minutes.
[Receiving the signal from the FM radio]
Hour → Minute → Sound source (FM) → Channel is selected. → Volume level when timer
playback starts → Playback time → Setting complete. (The current time is displayed.)
· The playback time is set in 5-minute increments from 10 to 30 minutes.
* Register desired broadcast stations in preset channels in advance.
[Sounding buzzer]
Hour → Minute → Sound source (bb/ buzzer) → Setting complete. (The current time is
displayed.)
* You cannot set the volume level of the buzzer.
* If you do not stop the buzzer, it keeps sounding for 3 minutes.
4
Switch the ALARM switch to “TIMER PLAY.”
appears on the display.
* When the ALARM switch is switched to “TIMER PLAY”, the Unit is locked with the power off.
n
Stopping Timer Playback
[Pausing timer playback (Snoozing function)]
Press the SNOOZE/BRIGHTNESS button during timer playback.
Timer playback stops temporarily but it restarts after 9 minutes. This operation repeats
up to 6 time.
[Stopping the timer playback]
Press the power button during timer playback.
Timer playback stops and it restarts at the same time the next day.
n
Cancelling the timer
Switch the ALARM switch to “ALARM OFF.”
SettingtheTimeroftheiPod,FMRadioorBuzzer
n
Listening to the radio
Extend the wire antenna to use it.
1
Turn on the power.
2
Select “FM” with the SOURCE button.
3
Select a frequency with the
4
/
¢
button.
· When you press and hold the
4
/
¢
button, the Unit automatically searches for
broadcast stations. The search is nished when a signal is picked up. Press the but-
ton again while searching is in progress to quit the search.
Button Function
6
Press to switch between the frequency and channel display.
¢
Press to raise the frequency or select a preset channel.
4
Press to lower the frequency or selects a preset channel.
Listening to FM Broadcasts
FM wire antenna
Pull the FM wire an-
tenna out of the pocket
in the battery compart-
ment cover and extend
the antenna along the
groove of the Unit and
in the direction where
you can get the best
radio reception.
AA battery
u
Connecting the AC adaptor
Wall outlet
AC 120 V, 60 Hz
AC adaptor (supplied)
RA-P1B : AA-R609
RA-P1W : AA-R610
n
Charging the iPod
1
Connect the AC adaptor to the Unit.
* The iPod battery is not charged while the Unit is operated on battery
power supply.
2
Set the iPod to the Unit.
Charging starts.
· The iPod is charged while any function of the Unit is used.
· The iPod is charged while the Unit is turned off.
* See the iPod instruction manual about charging times.
n
Registering broadcast station in preset channels
(Presetting)
You can preset up to 10 preferred stations (P01 to P10).
1
Select “FM” with the SOURCE button.
2
Press the
6
button.
A channel number is displayed.
3
Select your desired channel number with the
4
/
¢
button,
and press and hold the
6
button.
The channel number starts ashing.
4
Whilethechannelnumberisashing,usethe
4
/
¢
button to
select the frequency of the station that you wish to register and
press the
6
button.
The selected frequency will be registered in the selected channel.
* If you made a mistake or the setting disappeared because of a power failure or the like, start
over from Step 1.
n
Listening to the channel of a broadcast station you
registered
1
Press the
6
button while “FM” is selected.
A channel number is displayed and the signal of the registered frequency is picked up.
2
Select a channel number with the
4
/
¢
button.
The signal of the frequency registered to the selected channel number is picked up.
n
About the Display Indications
Functions used Displayednumbers,icons,etc.
Volume level adjustment 00 to 32
iPod iPod
FM radio
FM 87.5 to 108.0 MHz (Frequencies)
P01 to P10 (Channels)
External device Audio in 00 to 32 (Volume level)
Lights when the timer mode is selected.
Flashes while the Unit is snoozing.
Flashes when the remaining battery
level is low.